Lets see your current dump trucks!

[buffalonick]

Anyone that has a dump truck, new or used post some pictures of them. Lets see what you use Chevy, Ford, International.....

[02DURAMAX]

Here is one of my C4500 in winter mode

[Dirt Digger2]

here are a few I use to drive...

http://i288.photobucket.com/albums/ll165/dirtdigger2/1-28-09002.jpg
http://i288.photobucket.com/albums/ll165/dirtdigger2/1-28-09004.jpg

and my favorite...I loved this truck
http://i288.photobucket.com/albums/ll165/dirtdigger2/12-15-08008.jpg
http://i288.photobucket.com/albums/ll165/dirtdigger2/12-15-08010.jpg
http://i288.photobucket.com/albums/ll165/dirtdigger2/Heavy%20Equipment%20and%20Farming/Heavy%20Equipment%20and%20Farming%20Vidoes/th_12-15-08012.jpg (http://s288.photobucket.com/albums/ll165/dirtdigger2/Heavy%20Equipment%20and%20Farming/Heavy%20Equipment%20and%20Farming%20Vidoes/?action=view&current=12-15-08012.flv)
http://i288.photobucket.com/albums/ll165/dirtdigger2/Heavy%20Equipment%20and%20Farming/Heavy%20Equipment%20and%20Farming%20Vidoes/th_6-29-08003.jpg (http://s288.photobucket.com/albums/ll165/dirtdigger2/Heavy%20Equipment%20and%20Farming/Heavy%20Equipment%20and%20Farming%20Vidoes/?action=view&current=6-29-08003.flv)

[srl28]

Hey 02duramax....how is it salting with that small tailgate salter? do you run bags or bulk and shovel it in? What size lots do you do with that? Nice truck btw, and plow!

[Supper Grassy]

Nice Trucks!!

[Lawn Freak]

[QUOTE=Dirt Digger2;3190023]here are a few I use to drive...

Thats the same brake controller I have in my truck, good units

[JosephLawnCare]

hey 02, did you ever get around to painting/fixing the bed on the 4500? that's a damn nice truck.

[02DURAMAX]

hey 02, did you ever get around to painting/fixing the bed on the 4500? that's a damn nice truck.

Nope..:cry: Still on my to do list!

I will be getting the tailgate line-Xed in about a month before winter!

and atleast sandblast the truck bed and put some paint so it helps in the winter...If I don't have time to finish it this year.:dizzy:

[02DURAMAX]

Hey 02duramax....how is it salting with that small tailgate salter? do you run bags or bulk and shovel it in? What size lots do you do with that? Nice truck btw, and plow!

I run bag and bulk..so if its bulk i use a 5gal bucket and scoop it in from 1 Ton bins That I load on the truck. I no longer use the salter you see in the first pic "Pro-Flo 1"...In the second pic you can see part of the newer "Pro-Flo 2". Much better spreader! The Pro-Flo 2 is made to run bulk.

I do everything with it from banks, big commercial lots, Medical centers, & Strip malls.

I love the truck!

[TREEGUARD]

here's mine

[EA Quinn]

Only picture I have on my computer of one of the many dump trucks at work......
http://www.lawnsite.com/attachment.php?attachmentid=112610&stc=1&d=1214346430

[yardmanlee]

mine w/ leaf box on it

[mowerbrad]

mine w/ leaf box on it

Those wheels on the leaf loader look tiny, almost like the tires on a wheel barrow. Do you actually drive that down the road?

Nice truck tho.

[yardmanlee]

Those wheels on the leaf loader look tiny, almost like the tires on a wheel barrow. Do you actually drive that down the road?

Nice truck tho.

yes they are highway rated tires

[Dstosh]

http://i481.photobucket.com/albums/rr178/Dstosh/0419091312a.jpg

Kind of a bomb-Gets the job done though.

[scagmower]

heres mine only pict i could find, not the best pict

[srl28]

Boring slow night so heres 2 of mine. Not the best pictures either but you get the point. :usflag:

[BlackDog3]

Hey Gang, i haven't posted in a few months but i got myself a new dump truck in July. 1998 Chevy 3500HD 12 ft stake body. It has a newer 6.5 Diesel with 27,000 miles. So far its working out pretty good!

http://chevytruckworld.tenmagazines.com/gallery/Black%20Dog%203/292521.jpg

[Hoffman Lawn Care]

I mostly read to learn on this site but someone mentioned dump trucks :usflag:

86 GMC that has low miles, a manual trans and runs perfect. This is the best truck, I love this truck.

http://i32.tinypic.com/2przc6o.jpg

1956 IH that I'm working on getting the engine unstuck (first). I plan to use it for work sometimes.

http://i28.tinypic.com/f0n7ky.jpg

85 Ford diesel that I'm going to sell.

http://i29.tinypic.com/2m48592.jpg

[a&j lawncare llc]

the oil truck is my 9 to 5 job ride.. the ford is my persnal ride..

[BlackDog3]

That 86 is sharp. I have an older 82 K 30 that i used to use as my every day dump truck till i got the HD. Mine doesent exactly have low miles, almost 180,000 haha.

Chris

[syzer]

The old one:

http://www.precision-aquatics.com/gallery/albums/album04/Picture_065.jpg

The new one, just finished today, but didn't have time to get it. Ill post pics:

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0342.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0347.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0348.sized.jpg

[Twitchy]

This is one of our dumps. I have the pleasure of driving this everyday. Built Ford tough.

[Fordguy]

Here's 2 of mine

[E.L.Co]

The old one:

http://www.precision-aquatics.com/gallery/albums/album04/Picture_065.jpg

The new one, just finished today, but didn't have time to get it. Ill post pics:

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0342.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0347.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0348.sized.jpg

that is absolutely amazing! please post pics of it in action soon...some specs would be cool as well

[Crash]

2000 Chevy 3500HD/6.5L. Diesel - 5yd. Landscape Sides Dump
1983 Chevy 3500/350 - 3yd. Grain Body Dump
1979 Ford 350/351 Modified - 3yd. Landscape Sides Dump

[RHooper]

My toy is not a dump truck per say, but I did dump a lot of money on the table when I bought it. Does that count ? Here ya go !

[yardmanlee]

The old one:

http://www.precision-aquatics.com/gallery/albums/album04/Picture_065.jpg

The new one, just finished today, but didn't have time to get it. Ill post pics:

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0342.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0347.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album04/IMG_0348.sized.jpg

would like to see some close up pics of those doors w/ ramps and in diffrent positions if ya can, are you going to put some type of canopy across the top? mesh or solid?

[Hoffman Lawn Care]

1979 Ford 350/351 Modified - 3yd. Landscape Sides Dump

That is the best era of Ford for trucks. If my Ford was of that vintage I would keep it.

[Craaaig]

yes more pics and specs of that chevy crew cab please

[2brothersyardcare]

nice trucks every1

[kps2389]

I mostly read to learn on this site but someone mentioned dump trucks :usflag:

86 GMC that has low miles, a manual trans and runs perfect. This is the best truck, I love this truck.

http://i32.tinypic.com/2przc6o.jpg

1956 IH that I'm working on getting the engine unstuck (first). I plan to use it for work sometimes.

http://i28.tinypic.com/f0n7ky.jpg

85 Ford diesel that I'm going to sell.

http://i29.tinypic.com/2m48592.jpg

How about some info about the ford dump you want to sell I might be interested.

[nnj18]

I along with others would also like specks on the chevy....I'd prefer to know more about the dump body then the truck if possible? The ramp looks very interesting!!!!

[Hoffman Lawn Care]

How about some info about the ford dump you want to sell I might be interested.

Its got 154k (I think) and it runs ok, not great. Its a 4 speed manual. It starts hard sometimes and stalls occasionally when you let off the pedal quickly. The back brakes drag and need to be fixed. The starting and stalling are manageable but the brakes would need to be fixed before you put it to work. I just dont have the time to fix it. I want around $2700 for it. PM me if you are still interested.

[THEGOLDPRO]

Its got 154k (I think) and it runs ok, not great. Its a 4 speed manual. It starts hard sometimes and stalls occasionally when you let off the pedal quickly. The back brakes drag and need to be fixed. The starting and stalling are manageable but the brakes would need to be fixed before you put it to work. I just dont have the time to fix it. I want around $2700 for it. PM me if you are still interested.

what engine does it have??? and is it a 4x4?

[lawnangel1]

That crew cab is sick!!!!!!!

[PORTER 05]

me wanty that crew caby.

[westcoh]

97 International 4900. It's had it's issues but I couldn't get by without it.

[81Bronk36]

what engine does it have??? and is it a 4x4?

Its a 6.9L diesel... and no its definatly not a 4x4, look at the front hubs, or lack there of.

Not a horrible price. I just put 1700 into my 250, so I know how much they cost to maintain.

[srl28]

Nice truck, is that a custom color? Where did you get the paint job done? And if you dont mind my asking, how much did the paint job run ya? Beautiful set up

[AdamChrap]

Love that crew cab dump!

[syzer]

Hey guys, thanks for digging the truck! A lot of time, effort and money went into the darn thing. Let me know specifically what you are looking for and I will answer the best way I can.

You can see a bunch of High Res shots here:

http://www.precision-aquatics.com/gallery/album07

Here are some quick specs:

14' dump beaver tail
Doors in rear are both barn door and ramps
53" side gate with step ladder
Fuel tanks going on the side will be a 35g regular, 25g diesel, 25g mixed fuel
Intermediate dump gate controlled with air actuated cylinder and pins
Hoops are for a tarp for leaf removal

Here are some pics, still need to put the fuel tanks on, and stickers go on Friday if they can get their act together and need to order simulators.

http://www.precision-aquatics.com/gallery/albums/album07/IMG_0384.sized.jpghttp://www.precision-aquatics.com/gallery/albums/album07/IMG_0380.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album07/IMG_0382.sized.jpghttp://www.precision-aquatics.com/gallery/albums/album07/IMG_0381.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album07/IMG_0375.sized.jpghttp://www.precision-aquatics.com/gallery/albums/album07/IMG_0373.sized.jpg

http://www.precision-aquatics.com/gallery/albums/album07/IMG_0362.sized.jpghttp://www.precision-aquatics.com/gallery/albums/album07/IMG_0364.sized.jpg

[wayside]

syzer the truck looks good & that dump body super nice.

[ZKSLAWN]

uuuhhhhhhhhhhhhhhhhhhhhh wow? what words can describe that truck.. if i drive down there can i get a ride or something?? lol.. looks sick

[greatinmulchbeds]

hey you located on eastern ave? I think i drove by your shop the other day. awesome fleet you got there

[tthomass]

Nice truck, my concern would be the life of the ramps with the machine. Go slow!

[tthomass]

Chevy 4500 DMAX dump and International roll off.

[syzer]

Thanks guys!

Greatinmulchbeds: Yeah thats us, place is a mess, but its getting there.

TThomas: nice trucks I tried to get a hold of the dude in PA that you got the idea for that box from, but never replied to me. I didnt know someone else had one I was going to get one on this truck, but oh well.

The truck isnt used two haul the skid steer like that, I had the ramps built so that it could during snow or for what ever reason like small grade jobs, etc. It will be towed on a trailer.

[tthomass]

Check out ebay for some simulators for that truck too. Jarod has his hands full this year for sure and prob gets lots of messages..........idk. His trucks and mine are the only ones but if you ever need anything shoot me a message.

[syzer]

Yeah, thats where I was going to look, luckily now 22.5's are cheaper then they were just 6 months ago.

I appreciate the offer, same thing, need anything drop me a line.

[RHooper]

Hello,
Hey I agree with TThomas. I think a set of chrome simulators on those wheels would be awesome. That is truly a killer truck. You make me feel bad now, cause I thought I had a little something with my LCF landscaper. You should be proud of that truck. That's AWESOME ! Congrats

Rick

[RHooper]

Hey, I see you 're in Maryland. Anywhere near Ellicott City? I've got some relatives up there. Again, awesome truck !

Rick

[yardmanlee]

syze, great looking truck!!!

[E.L.Co]

thanks scyzor for postin more pics, that is one of the coolest trucks ive seen... i luv those heavy duty chevys

[Lawn Tek]

No trailers , yipeee ! Sweet !

[Marek]

Nice body on that truck syzer, who did you have do it ?

[syzer]

Hey, I see you 're in Maryland. Anywhere near Ellicott City? I've got some relatives up there. Again, awesome truck !

Rick

Thanks! We are about 45 minutes away from Ellicott City, we do a bit of work around there.

Nice body on that truck syzer, who did you have do it ?

Thanks Marek, the body was built by Intercon Truck Company off of Philadelphia Rd. They do great work!


Thanks again guys!

[srl28]

Syzer, beautiful truck, What else ya got?

[pitrack]

Hey guys, thanks for digging the truck! A lot of time, effort and money went into the darn thing. Let me know specifically what you are looking for and I will answer the best way I can.

You can see a bunch of High Res shots here:

http://www.precision-aquatics.com/gallery/album07

Here are some quick specs:

14' dump beaver tail
Doors in rear are both barn door and ramps
53" side gate with step ladder
Fuel tanks going on the side will be a 35g regular, 25g diesel, 25g mixed fuel
Intermediate dump gate controlled with air actuated cylinder and pins
Hoops are for a tarp for leaf removal

Here are some pics, still need to put the fuel tanks on, and stickers go on Friday if they can get their act together and need to order simulators.


Wow, looks awesome.

[Craaaig]

Looks Great! I'd love to have one of those

[syzer]

Syzer, beautiful truck, What else ya got?

Thanks, we have all kinds of stuff. Maybe Ill start a thread one of these days.


Thanks guys for the kind words

[Ben's Landscape]

WOW that is a huge dump syzer!! How many yards will it hold??

[Twitchy]

Damn Syzer, that dump has more moving parts than a Transformer!!! Sweet dump! What gauge steel did you go with??? And good luck keeping that thing clean during pollen season.

[P.Services]

I hear by make the notion to award syzer as the winner for "The most awesome truck on lawnsite" all in favor say ehh

I could drool over that thing all day long. Can you please tell us what that body cost $$$??

[syzer]

WOW that is a huge dump syzer!! How many yards will it hold??

I think it will hold around 15 yards, I guess more heaped up.

Damn Syzer, that dump has more moving parts than a Transformer!!! Sweet dump! What gauge steel did you go with??? And good luck keeping that thing clean during pollen season.

Thanks bro, I almost put a lift gate on the side, but last minute change eliminated that. Its thick stuff, I cant remember the gauge. Its tough keeping the black trucks clean, but they usually get washed once a week so they stay pretty.

I hear by make the notion to award syzer as the winner for "The most awesome truck on lawnsite" all in favor say ehh

I could drool over that thing all day long. Can you please tell us what that body cost $$$??

Thanks man! =). I think the bed alone was around 24kish. Set me back a good bit, but it will be worth it once this thing gets to making some money!

[Lawn Tek]

Contest to guess how much it cost lettered ,complete ?

My guess ,66,972.33:drinkup:

[E.L.Co]

72,365.79 theres my guess! and yes he gets the award but...i move that we force him to get that picture thread going because i bet his wb mowers are even coooool:laugh::drinkup:

[P.Services]

oh come on you really paid 24k for that bad!!!!!!!!!!! i was thinking 10-15. $24,000 really wow.

i say $78,200.00

[nnj18]

wow I'd never spend 24k on a dump body!! WOW!!! Nice truck though!!!

I'm gonna guess $83,459.28
Posted via Mobile Device

[Hanau]

$100K +.

The comparitively plain jane International 4300 I want is $98K.

Commercial truck prices are nutso.

[P.Services]

No way is a plain jane 4300 going for 98 grand. That may be msrp but they arnt getting that. What kinda 4300 is it? Crew cab dumper or what?
Posted via Mobile Device

[Hanau]

No way is a plain jane 4300 going for 98 grand. That may be msrp but they arnt getting that. What kinda 4300 is it? Crew cab dumper or what?
Posted via Mobile Device

Let me see if I can work some magic on my computer and upload the quote. It's in a PDF.

Crew cab, auto, DT466, big dump body, Knap Pack, Tommy Gate Lift N' Dump, cloth seats, A/C, CD player, you get the idea.

It was my dream truck until I got the quote.

[Hanau]

I'm getting an error message when I try to atach the pdf. Might be too big. It's 7 pages. I'll cut and paste.

Model Profile
2010 4300 SBA 4X2 (MA025)
APPLICATION: Landscape Dump
MISSION: Requested GVWR: 25500. Calc. GVWR: 25500
Calc. Start / Grade Ability: 51.90% / 2.96% @ 55 MPH
Calc. Geared Speed: 75.1 MPH
FUEL ECONOMY: 8.02 MPG @ 55 MPH
DIMENSION: Wheelbase: 236.00, CA: 125.00, Axle to Frame: 96.00
ENGINE, DIESEL: {International MaxxForce DT} 255 HP, 660 lb-ft Torque @ 1400 RPM, 2600 RPM Governed
Speed, # 2 Bell Housing
TRANSMISSION, AUTOMATIC: {Allison 3500_RDS_P} 4th Generation Controls; Wide Ratio, 5-Speed, With Overdrive; On/Off
Hwy; Includes Oil Level Sensor, With PTO Provision, Less ******er, With 80,000-lb GVW & GCW
Max.
CLUTCH: Omit Item (Clutch & Control)
AXLE, FRONT NON-DRIVING: {Meritor MFS-10-122A} I-Beam Type, 10,000-lb Capacity
AXLE, REAR, SINGLE: {Meritor MS-19-14X-3DCL} Single Reduction, 19,000-lb Capacity, With 190 Wheel Ends, Driver
Controlled Locking Differential Gear Ratio: 5.57
CAB: Conventional 6-Man Crew Cab
TIRE, FRONT: (2) 11R22.5 G395 LHS (GOODYEAR) 504 rev/mile, load range G, 14 ply
TIRE, REAR: (4) 11R22.5 G622 RSD (GOODYEAR) 497 rev/mile, load range G, 14 ply
SUSPENSION, RR, SPRING, SINGLE:Vari-Rate; 15,500-lb Capacity, With 4500 lb Auxiliary Rubber Spring
PAINT: Cab schematic 100GA
Location 1: 9219, Winter White (Std)
Chassis schematic N/A
August 10, 2009
1 Proposal: 7509-01
Description
Base Chassis, Model 4300 SBA 4X2 with 236.00 Wheelbase, 125.00 CA, and 96.00 Axle to Frame.
TOW HOOK, FRONT (2) Inside Rail, Frame Mounted.
FRAME RAILS High Strength Low Alloy Steel (50,000 PSI Yield); 10.125" x 3.062" x 0.312" (257.2mm x 77.8mm x 8.0mm);
480.1" (12195mm) Maximum OAL
BUMPER, FRONT Full Width, Aerodynamic, Heavy Duty, Steel
Includes
: BUMPER, FRONT Powder Coated Gray (Argent) Color
CROSSMEMBER, REAR, AF (01)
WHEELBASE RANGE 199" (505cm) Through and Including 254" (645cm)
AXLE, FRONT NON-DRIVING {Meritor MFS-10-122A} I-Beam Type, 10,000-lb Capacity
SUSPENSION, FRONT, SPRING Parabolic, Taper Leaf; 10,000-lb Capacity; With Shock Absorbers
Includes
: SPRING PINS Rubber Bushings, Maintenance-Free
BRAKE SYSTEM, HYDRAULIC {Meritor-Wabco} Split System, Full Power, With Automatic Adjustment And With Four Channel ABS
BRAKE CHAMBERS, FRONT AXLE {Haldex} 20 SqIn
BRAKE CHAMBERS, REAR AXLE {MGM MJS3028ET} 30/28 Piston Spring Brake
BRAKE, PARKING {Bosch} DSSA Type, 12" x 3"; for Hydraulic Brake Chassis; Activated by Lever in Cab; Differential Mounted
Includes
: PARKING BRAKE CONTROL Lever, Floor Mounted, Located Right of Driver
BRAKES, FRONT, HYDRAULIC DISC Quadraulic; four 70mm Diameter Pistons
BRAKES, REAR, HYDRAULIC DISC Quadraulic; four 70mm Diameter Pistons
AIR COMPRESSOR {Bendix Tu-Flo 550} 13.2 CFM Capacity; and Tank for Air Source on Hydraulic Chassis
STEERING COLUMN Stationary
STEERING WHEEL 2-Spoke, 18" Diam., Black
STEERING GEAR {Sheppard M-100} Power
DRIVESHAFT {Dana Spicer} SPL140 in lieu of SPL90 Series
EXHAUST SYSTEM Single, Horizontal, Aftertreatment Device, Frame Mounted Right Side Back of Cab, Includes Horizontal Tail Pipe
Includes
: NOTE: The Horizontal Tailpipe Includes a Temperature Control Device
ENGINE BRAKE, DLOGIC {Diamond Logic} for MaxxForce DT Engines; Combination Engine and Exhaust Brake, Electronically Activated
ELECTRICAL SYSTEM 12-Volt, Standard Equipment
Includes
: BATTERY BOX Steel
: DATA LINK CONNECTOR For Vehicle Programming and Diagnostics In Cab
: FUSES, ELECTRICAL SAE Blade-Type
: HAZARD SWITCH Push On/Push Off, Located on Top of Steering Column Cover
: HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever
: HORN, ELECTRIC Single
: JUMP START STUD Located on Positive Terminal of Outermost Battery
: PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light
: STARTER SWITCH Electric, Key Operated
Vehicle Specifications August 10, 2009
2010 4300 SBA 4X2 (MA025)
2 Proposal: 7509-01
Description
: STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector
: TURN SIGNAL SWITCH Self-Cancelling for Trucks, Manual Cancelling for Tractors, with Lane Change Feature
: TURN SIGNALS, FRONT Includes Reflectors and Auxiliary Side Turn Signals, Solid State Flashers; Flush Mounted
: WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature (5 Pre-Set Delays), Integral with Turn Signal Lever
: WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted
: WIRING, CHASSIS Color Coded and Continuously Numbered
CIGAR LIGHTER Includes Ash Cup
ALTERNATOR {Leece-Neville LBP2224H} Brush Type; 12 Volt 120 Amp. Capacity, Pad Mounted
BODY BUILDER WIRING Rear of Frame; Includes Sealed Connectors for Tail/Amber Turn/Marker/ Backup/Accessory Power/Ground and
Sealed Connector for Stop/Turn
BATTERY SYSTEM {International} Maintenance-Free, (3) 12-Volt 1950CCA Total
RADIO {International} AM/FM Stereo With CD Player, Weatherband, Clock, Auxiliary Input, Includes Multiple Coaxial Speakers
Includes
: SPEAKERS IN CAB (2) Coaxial with Deluxe Interior
: SPEAKERS IN CAB (4) Coaxial with Premium Interior
JUMP START STUD Remote Mounted
STARTING MOTOR {Delco Remy 38MT Type 300} 12 Volt; less Thermal Over-Crank Protection
HEADLIGHTS Halogen; Composite Aero Design for Two Light System
GRILLE Chrome
FRONT END Tilting, Fiberglass, With Three Piece Construction
PAINT SCHEMATIC, PT-1 Single Color, Design 100
Includes
: PAINT SCHEMATIC ID LETTERS "GA"
PAINT TYPE Base Coat/Clear Coat, 1-2 Tone
SPECIAL RATING, GVWR Limited to 25,999-lb GVWR
CLUTCH Omit Item (Clutch & Control)
ENGINE, DIESEL {International MaxxForce DT} 255 HP, 660 lb-ft Torque @ 1400 RPM, 2600 RPM Governed Speed, # 2 Bell Housing
Includes
: AIR COMPRESSOR AIR SUPPLY LINE Naturally-Aspirated
: COLD STARTING EQUIPMENT Intake Manifold Electric Grid Heater with Engine ECM Control
: CRUISE CONTROL Electronic; Controls Integral to Steering Wheel
: ENGINE OIL DRAIN PLUG Magnetic
: ENGINE SHUTDOWN Electric, Key Operated
: FUEL FILTER Included with Fuel/Water Separator
: FUEL/WATER SEPARATOR Fuel/Water Separator and Fuel Filter in a Single Assembly; With Water-in-Fuel Sensor; Engine Mounted
: GOVERNOR Electronic
: OIL FILTER, ENGINE Spin-On Type
: WET TYPE CYLINDER SLEEVES
FAN DRIVE {Borg-Warner SA85} Viscous Type, Screw On
Includes
: FAN Nylon
FEDERAL EMISSIONS for 2004; for International VT365, DT466 and DT570 Engines
RADIATOR Aluminum; 2-Row, Cross Flow, Over Under System, 717 SqIn Louvered, With 313 SqIn Charge Air Cooler. With In-Tank
Transmission Cooler
Vehicle Specifications August 10, 2009
2010 4300 SBA 4X2 (MA025)
3 Proposal: 7509-01
Description
Includes
: ANTI-FREEZE Red Shell Rotella Extended Life Coolant -40F (-40C)
: DEAERATION SYSTEM with Surge Tank
: HOSE CLAMPS, RADIATOR HOSES Gates Shrink Band Type; Thermoplastic Coolant Hose Clamps
: RADIATOR HOSES Premium, Rubber
AIR CLEANER Single Element
Includes
: GAUGE, AIR CLEANER RESTRICTION Air Cleaner Mounted
THROTTLE, HAND CONTROL Engine Speed Control; Electronic, Stationary, Variable Speed; Mounted on Steering Wheel
ENGINE CONTROL, REMOTE MOUNTED - No Provision Furnished for Remote Mounted Engine Control
FEDERAL EMISSIONS 2007 for International MaxxForce DT Engines (DT466)
EXPANDED ENGINE TEMP EFFECTS to Allow Higher Engine Operating Temperature Range; Includes Nylon Surge Tank and 15 psi
Pressure Cap
EMISSION COMPLIANCE Federal, Does Not Comply With California Clean Air Regulations
TRANSMISSION, AUTOMATIC {Allison 3500_RDS_P} 4th Generation Controls; Wide Ratio, 5-Speed, With Overdrive; On/Off Hwy;
Includes Oil Level Sensor, With PTO Provision, Less ******er, With 80,000-lb GVW & GCW Max.
Includes
: OIL FILTER, TRANSMISSION Mounted on Transmission
: TRANSMISSION OIL PAN Magnet in Oil Pan
TRANSMISSION SHIFT CONTROL {Allison} Push-Button Type; for Allison 3000 & 4000 Series Transmission
SHIFT CONTROL PARAMETERS WT-Allison S-1 Performance Programming in Primary and Allison S-4 Economy Programming in
Secondary
ALLISON SPARE INPUT/OUTPUT for Rugged Duty Series (RDS); General Purpose Trucks, Construction
AXLE, REAR, SINGLE {Meritor MS-19-14X-3DCL} Single Reduction, 19,000-lb Capacity, With 190 Wheel Ends, Driver Controlled Locking
Differential . Gear Ratio: 5.57
SUSPENSION, RR, SPRING, SINGLE Vari-Rate; 15,500-lb Capacity, With 4500 lb Auxiliary Rubber Spring
FUEL TANK (2) Top Draw; D Style, Steel, 50 U.S. Gal., Total Capacity 100 U.S. Gal., 378 L; 16" Tank Depth, Mounted Under Cab Left
and Right Side
CAB Conventional 6-Man Crew Cab
Includes
: ARM REST (2) Molded Plastic; One Each Door
: CLEARANCE/MARKER LIGHTS (5) Flush Mounted
: COAT HOOK, CAB Located on Rear Wall, Centered Above Rear Window
: CUP HOLDERS Two Cup Holders, Located in Lower Center of Instrument Panel
: DOME LIGHT, CAB Rectangular, Door Activated and Push On-Off at Light Lens, Timed Theater Dimming, Integral to Console, Center
Mounted
: GLASS, ALL WINDOWS Tinted
: GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side
: GRAB HANDLE, CAB INTERIOR (2) Front of "B" Pillar Mounted, One Each Side
: GRAB HANDLE, CAB INTERIOR (4) Two Each Side, Rear Door Mounted at Hinge Side and "C" Pillar Mounted
: INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color
: STEP (8) Two Steps Per Door
GAUGE CLUSTER English With English Electronic Speedometer
Includes
: GAUGE CLUSTER (5) Engine Oil Pressure (Electronic), Water Temperature (Electronic), Fuel (Electronic), Tachometer (Electronic),
Voltmeter
Vehicle Specifications August 10, 2009
2010 4300 SBA 4X2 (MA025)
4 Proposal: 7509-01
Description
: ODOMETER DISPLAY, Miles, Trip Miles, Engine Hours, Trip Hours, Fault Code Readout
: WARNING SYSTEM Low Fuel, Low Oil Pressure, High Engine Coolant Temp, and Low Battery Voltage (Visual and Audible)
IP CLUSTER DISPLAY Omit Display of Fault Codes in Instrument Cluster and Disable Blink Codes, Requires Service Tool to Retrieve
and View Fault Code
SEAT, DRIVER {National 2000} Air Suspension, High Back With Integral Headrest, Cloth, Isolator, 1 Chamber Lumbar, 2 Position Front
Cushion Adjust, -3 to +14 Degree Back Angle Adjust
Includes
: SEAT BELT 3-Point, Lap and Shoulder Belt Type
SEAT, PASSENGER {Gra-Mag} Non Suspension, High Back, Fixed Back, Integral Headrest, Cloth
Includes
: SEAT BELT 3-Point, Lap and Shoulder Belt Type
SEAT, REAR {International} BENCH; Full Width; Cloth, With Fixed Back and Two Integral Outboard Headrests
Includes
: SEAT BELT (3) Two 3-Point Shoulder Belts for Driver and Outer Passenger and One 2-Point Lap Belt for Center Passenger
MIRRORS (2) {Lang Mekra} Rectangular, 7.44" x 14.84" & 7.44" sq. Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated
Heads Thermostatic Controlled, Black Heads, Brackets and Arms
INSTRUMENT PANEL Center Section, Flat Panel
AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster
Includes
: HEATER HOSES Premium
: REFRIGERANT Hydrofluorocarbon HFC-134A
CAB INTERIOR TRIM Deluxe; for Crew Cab
Includes
: "A" PILLAR COVER Molded Plastic
: CAB INTERIOR TRIM PANELS Cloth Covered Molded Plastic, Full Height; All Exposed Interior Sheet Metal is Covered Except for the
Following: with a Two-Man Passenger Seat or with a Full Bench Seat the Back Panel is Completely Void of Covering
: CONSOLE, OVERHEAD Molded Plastic; With Dual Storage Pockets with Retainer Nets and CB Radio Pocket
: DOOR TRIM PANELS Molded Plastic; Driver and Passenger Doors
: FLOOR COVERING Rubber, Black
: HEADLINER Soft Padded Cloth
: INSTRUMENT PANEL TRIM Molded Plastic with Black Center Section
: STORAGE POCKET, DOOR (1) Molded Plastic, Full-Length; Driver Door
: SUN VISOR (2) Padded Vinyl with Driver Side Toll Ticket Strap, Integral to Console
CAB REAR SUSPENSION Air Bag Type
WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10 Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC
Rims; With Steel Hubs.
Includes
: PAINT IDENTITY, FRONT WHEELS White
: WHEEL SEALS, FRONT Grease Lubricated, Includes Wheel Bearings
WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25
DC Rims; With Steel Hubs
Includes
: PAINT IDENTITY, REAR WHEELS White
: WHEEL SEALS, REAR Oil Lubricated, Includes Wheel Bearings
(2) TIRE, FRONT 11R22.5 G395 LHS (GOODYEAR) 504 rev/mile, load range G, 14 ply
Vehicle Specifications August 10, 2009
2010 4300 SBA 4X2 (MA025)
5 Proposal: 7509-01
Description
(4) TIRE, REAR 11R22.5 G622 RSD (GOODYEAR) 497 rev/mile, load range G, 14 ply
14' Allied Flatbed (Per Customer Specs)
Vehicle Specifications August 10, 2009
2010 4300 SBA 4X2 (MA025)
6 Proposal: 7509-01
(USA DOLLAR)
Description Price
Factory List Prices:
Product Items $90,740.00
Service Items $0.00
Total Factory List Price Including Options: $90,740.00
Pre Delivery Inspection, Detail and
Fuel for Delivery
$421.36
Interest calculated per month at
$546.39 for the chassis for a total of
$1639.17
$1,639.17
Total Preparation And Delivery: $2,060.53
Freight Charge $1,750.00
Total Freight: $1,750.00
Total Factory List Price Including Freight: $94,550.53
Less Customer Allowance: ($18,687.78)
Total Vehicle Price: $75,862.75
Total Body/Allied Equipment: $22,300.36
Total Sale Price: $98,163.11
Total Per Vehicle Sales Price: $98,163.11
Net Sales Price: $98,163.11
Please feel free to contact me regarding these specifications should your interests or needs change. I am confident you will be
pleased with the quality and service of an International vehicle.

Since the black monster is much fancier than this truck I'd venture to say his truck cost over 100K. The body cost on the truck I want is $22,300.36

Heck the truck I want doesn't even have chrome bumpers or mirror caps.

At this price I'm looking for a 08 or 09 Chevy Kodiak 5500 crew cab 4x4 that's sitting on a lot somewhere. Those run in the mid fifties I believe. Not as huge (the 4300 comes in at 30 feet) but a heckuva lot cheaper.

Truck prices are nuts!:hammerhead:

[syzer]

oh come on you really paid 24k for that bad!!!!!!!!!!! i was thinking 10-15. $24,000 really wow.

i say $78,200.00

Thanks again guys!

Yeah 24k for it, steep but worth it. I got a few prices one from the guys in MA who built the Nicolazza landscaping trucks they wanted 30k and it wasn't as nice as this bed I dont think. In the North East prices on EVERYTHING are ridiculous!

Not sure what the whole thing will run said and done, I will try to add it up tomorrow. Probably around 85-90k. Tags for it today were $4,700.00. Good ole' Maryland!

[oakhillslandscaping]

Thanks again guys!

Yeah 24k for it, steep but worth it. I got a few prices one from the guys in MA who built the Nicolazza landscaping trucks they wanted 30k and it wasn't as nice as this bed I dont think. In the North East prices on EVERYTHING are ridiculous!

Not sure what the whole thing will run said and done, I will try to add it up tomorrow. Probably around 85-90k. Tags for it today were $4,700.00. Good ole' Maryland!

do you mean New England truck design?.... they arent that great. they are good but i think you were better off with someone closer to you but thats just my opinion. i like your truck its truely one of a kind

[syzer]

do you mean New England truck design?.... they arent that great. they are good but i think you were better off with someone closer to you but thats just my opinion. i like your truck its truely one of a kind

Yeah, thats the company. Seem like good work, but cant tell until you see. I am very happy with my choice, they are the only ones I know of doing the gate that swings like barn doors or ramps. That will be extremely useful. Thanks.

[rusty_keg_3]

One of my brothers, Mike is a VP of a construction type company, they dont build buildings tho. Its They do like supports for bridges, and arenas, and other stuff like that... Anywho, he also owns KEGZ Trucking, LLC... He bought his first dump a few years ago, and this spring he bought a nice newish Ford L9000... Well, his driver was out, with a full load, when he blew a front tire, and flipped the truck end over end...Well, it was a total loss... SO he went out and bought this Peterbilt 4 Axle... It will hold 20 Tons, i dont know much about his other one(s), but i will find out... The red Ford is his, and the other red one is his friends, but i think he is buying it...

Actualy, i just started working for him, i clean his trucks... I also do a little yard work. He is going to teach me how to drive these, and once im 18 i will get my CDL, and i might drive for him in my spare time. Oh, and i want to learn how to use a bulldozer (he has a few)...


Well, heres the trucks, i know they arent very clean, but he just got done dredging the river, so they are nasty...

[rusty_keg_3]

Heres the other ones....

And a old bulldozer behind one of his barns...

He also has a F650, with a big service bed...