PDA

View Full Version : Hustler trimstar 36" quality of cut


cudaaa
05-26-2010, 08:34 PM
I am having cut quality problems! When I bought the machine it had stock blades that where wore out. The first blades I bought where gators worked great. But I bought the wavey mulchers & mulch plug & the stock blades. Now if I use ether of those I get a stripe about where the 2 blades meet. The part #'s are

wavey blades
794214- 20 5/16 long
724206- 13 1/2 long

Normal lift
793794- 20 7/16 long
793802- 13 5/8 long

gator
794222- 13 11/16 long
oregon gator (Bought from Hustler Dealer)
96-335- 20 7/16 long

The gator blades give a great cut
The wavey blades leave a bad stripe that needs to be cut twice.
The stock blades are not as bad but still needs double cutting.
The machine is a 06 trimstar 36" # 927400 with only 450hr on the clock.
Doesn't look like any modes done at all.
The deck is clean & adjusted Level with 1/8" higher to the back according to the manual.
Any help would be greatly appreciated!!!

mowerconsultant
05-28-2010, 02:58 PM
The measurements you have are not the same as what I have.
Are the blades your measuring new?

Fusion blades, stock on your mower from the factory.
side discharge (right blade) 600901 BLADE, F20.50"
side discharge (left blade) 600900 BLADE, F13.75"

Gator (right blade) 794230 BLADE, 20.50"
Gator (left blade) 794222 BLADE, 13.75"

mulching (right blade) 794214 BLADE, 20.50"
mulching (left blade) 794206 BLADE, 13.75"

cudaaa
05-28-2010, 06:51 PM
The blades where new this year. The stock blades are only a week old.
My mower is the 927400 not 929232 is there a differance.
The measurements is what I measured on the blade itself total overall length.

cudaaa
05-31-2010, 07:55 PM
Update:
After playing this weekend I discovered the main blade belt drive spring pressure a little loose. So after setting it at 5.5" according to spec the motor would die when I engaged the blades (slow or fast RPM) after playing around for 5 min or so engaging blades it started working! Any idea why? Do I have a problem with the blade drive clutch? Now that it is working it appears to be cutting better I will know after mowing this week!

blackandgold
05-31-2010, 11:50 PM
Unbolt the front blow out baffles near the front edge of the deck and remove them. This should help quite a bit.

mowerconsultant
06-01-2010, 08:59 AM
Engaging it at 3/4 throttle once the engine is warmed up should work fine.
I would make sure the idlers and spindles are all turning freely, remove the deck belt and turn them by hand to make sure.
Your deck belt tension would cause the cutting issue you had.

Pj

cudaaa
06-01-2010, 10:28 PM
(Blackandgold) I had thought about adding the blowout baffle mine does not have one installed. I take it they do not work well?

(Mowerconsultant) I had everything off & the blades turn freely spinals are tight.
It seems everytime after adjusting the spring pressure it wants to kill the motor when you engage the blades then after trying several times they engage & work fine. Is this normal?

Thanks for the Help!

mowerconsultant
06-02-2010, 09:16 AM
Try engaging it at a higher rpm.
Also, be ready to choke the engine a little if it starts to die.
This is something that is normal for the most part.

Pj