Register free!

The Green Industry's Resource Center



Reply
 
Thread Tools   Display Modes
  #1  
Old 02-09-2013, 09:13 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
How to paint a Mower

For the purist out there, this is not for you. In the space of one weekend (or day) you can revitalize a beat up mower. The deck we are looking at was done by me 4 years ago. Medium use after that. Tools required:

1) Drill with wire brush

2) Small Sander

3) Angle Grinder

You can get away with just a drill and wire brush if you need to.
Attached Images
     
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #2  
Old 02-09-2013, 09:15 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
First step is to pull off everything you don't want to paint or that will get in the way. KEEP ALL THE PARTS TOGETHER.
Attached Images
 
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #3  
Old 02-09-2013, 09:24 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
Next, wire brush, sand (60 grit), grind the surfaces. If I can't get the loose paint off with the brush or paper I just grind. You can see some of the really tight areas with rust, I just do the best i can with them. This is not a factory finish. You can continue sanding with finer grit if you want to, the more prep the better the end result will be.
Attached Images
           
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #4  
Old 02-09-2013, 09:32 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
Tape you bolt heads, etc. Looks better. Two coats of Self Etching Primer. Why? From the little bit of research I have done, Self Etching primer provides better contact on bare metal.
Attached Images
 
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #5  
Old 02-09-2013, 09:33 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
2 Coats of Paint
Attached Images
 
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #6  
Old 02-09-2013, 09:35 PM
IRRITECH's Avatar
IRRITECH IRRITECH is offline
LawnSite Senior Member
 
Join Date: Dec 2003
Location: ATLANTA, GA
Posts: 931
2 Coats of clear coat , and truck liner on the side and mulch plate (background)
Attached Images
 
__________________
The reigning Mayor of Stupidville
Reply With Quote
  #7  
Old 02-09-2013, 10:45 PM
jlong10's Avatar
jlong10 jlong10 is offline
LawnSite Member
 
Join Date: Jun 2011
Location: Anderson, SC
Posts: 27
How to paint a Mower

Looks good! I did the same thing to my mower last year and used the same primer. The paint looks pretty good other than some wear in normal areas. It's obviously not as good as powder coating, but is inexpensive and looks better than being scratched all to hell.
Reply With Quote
  #8  
Old 02-10-2013, 02:25 AM
Lbilawncare's Avatar
Lbilawncare Lbilawncare is offline
LawnSite Bronze Member
 
Join Date: May 2002
Location: Illinois
Posts: 1,108
I use a twisted wire wheel on a grinder, blasts off the paint easily. I take mine down to bare metal when I do them. Etching primer is best for bare metal, but it needs to be primed over with regular primer before painting. I buy my paint from sherwin-williams automotive and spray it with a hvlp gun.
__________________
Just cutting the grass just doesn't cut it.
Reply With Quote
  #9  
Old 02-10-2013, 11:34 AM
teckjohn teckjohn is offline
LawnSite Member
 
Join Date: Aug 2010
Location: Enterprise Alabama
Posts: 226
I used a sand blaster and it cleans it off pretty good

Harbor Freight has a few there for like 100 bucks
Reply With Quote
  #10  
Old 02-14-2013, 09:05 PM
dboyd351 dboyd351 is offline
LawnSite Senior Member
 
Join Date: Sep 2010
Location: Cape Charles, VA
Posts: 913
Quote:
Originally Posted by teckjohn View Post
Harbor Freight has a few there for like 100 bucks
Sandblasters are great for getting in all those tight spaces that are impossible to reach with a wire wheel.

Irritech's job looks pretty pretty darn good anyway, though.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 05:36 PM.

Page generated in 0.09276 seconds with 8 queries