Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #1  
Old 07-01-2001, 08:12 PM
slytiger slytiger is offline
LawnSite Member
 
Join Date: Jun 2001
Location: Bonaire, Georgia
Posts: 3
Backfiring engine

I've got a 12HP B&S engine on a Lowes/MTD riding mower. Periodicaly the engine backfires when I go around a corner, or when I disengage the blades and put the mower in neutral. Is this normal? This sort of thing happened to me before, and the engine ended up throwing a rod. I don't want that to happen again, any preventive advice, checks?
Reply With Quote
  #2  
Old 07-07-2001, 11:18 PM
ron ron is offline
LawnSite Senior Member
 
Join Date: Aug 2000
Location: Port Orange Fl 32119
Posts: 312
Ok try this
1.lower your RPM before shutting off the engine.
2. turn fuel shut off valve next to you gas tank and let the motor run itself out.
This works great for me with my Scag 36 in WB
Reply With Quote
  #3  
Old 07-08-2001, 07:03 AM
Richard Martin's Avatar
Richard Martin Richard Martin is offline
LawnSite Fanatic
 
Join Date: Mar 2000
Location: Greenville, NC
Posts: 14,499
Or you can lift the battery up, slide the riding tractor out from under it and slide a commercial mower under it that has a real engine. Drop the battery into the commercial mower and wham, problem fixed.
__________________
Serving Greenville, Winterville and Ayden NC



Reply With Quote
  #4  
Old 07-17-2001, 12:27 PM
MrFikit MrFikit is offline
LawnSite Member
 
Join Date: Apr 2001
Location: Norheast, Oh
Posts: 28
What sounds like is you may be getting an excess of fuel into the combustion chamber. What would normally cause this is the wrong float bowl setting. Get yourself a nice manual on 12HP Briggs engines and it will tell you how to go about doing it. Normally, you just remove the carb, remove the bowl on the bottom, turn it upside-down, then measure the distance between the bowl mounting surface and the bottom (in this position) of the float (usually not more than maybe 1/4" to 3/8") look at the book. There is a tab at the pivot side of the float which controls the depth of the needle valve. If you insert a screwdriver into or under that tab and bend it, you can achieve the desired height. Also, it never hurts to keep-up with regular maintenance such as spark plug, air cleaner, etc. Hope this helps.
Reply With Quote
  #5  
Old 07-27-2001, 05:47 PM
Fish's Avatar
Fish Fish is offline
LawnSite Member
 
Join Date: Feb 2001
Location: Lawrenceburg, KY
Posts: 139
Sounds like a layer of water in the bottom of the carb bowl. Dump
it out and see what happens.
Fish
Reply With Quote
  #6  
Old 07-28-2001, 12:04 PM
Fish's Avatar
Fish Fish is offline
LawnSite Member
 
Join Date: Feb 2001
Location: Lawrenceburg, KY
Posts: 139
Also could be that the kill wire to the switch at your forward
/reverse lever is has come unplugged and is close to metal.
Take the two phillips screws off of the panel and lift it up and
see. The seat switch is another problem area .
Fish
Reply With Quote
  #7  
Old 08-06-2001, 01:39 PM
williamslawn williamslawn is offline
LawnSite Member
 
Join Date: Mar 2001
Location: SC
Posts: 202
Sounds like the seat switch to me.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 01:53 PM.

Page generated in 0.08068 seconds with 9 queries