Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #11  
Old 11-20-2012, 04:48 PM
dstifel's Avatar
dstifel dstifel is online now
LawnSite Senior Member
 
Join Date: Oct 2012
Location: des moines ia
Posts: 776
What do you do with the ones that are pull start?
Reply With Quote
  #12  
Old 11-20-2012, 04:56 PM
larryinalabama larryinalabama is online now
LawnSite Fanatic
 
Join Date: Jan 2008
Location: Ragland Al
Posts: 10,012
Quote:
Originally Posted by dstifel View Post
What do you do with the ones that are pull start?
They will usually start if its above freezing, other wise I have to use starting fluid. My single cylinder 13hp will break your wrist if your not careful. I try too keep them where they dont have to be moved if they dont start.
Reply With Quote
  #13  
Old 11-20-2012, 06:12 PM
Tmurph2960 Tmurph2960 is offline
LawnSite Member
 
Join Date: Oct 2012
Posts: 10
it discribes the procedure for adjusting the valves in the service manual. They need to be checked every 300 hours. It is very easy to do. Also it is recommended to use 5w30 oil in cold weather. My last oil change of the season is with the light wieght oil. it is not as thick when cold.
Reply With Quote
  #14  
Old 11-20-2012, 06:14 PM
larryinalabama larryinalabama is online now
LawnSite Fanatic
 
Join Date: Jan 2008
Location: Ragland Al
Posts: 10,012
Quote:
Originally Posted by Tmurph2960 View Post
it discribes the procedure for adjusting the valves in the service manual. They need to be checked every 300 hours. It is very easy to do. Also it is recommended to use 5w30 oil in cold weather. My last oil change of the season is with the light wieght oil. it is not as thick when cold.
I dont have a manual, dou perhaps know what the valve clearance is?
Reply With Quote
  #15  
Old 11-20-2012, 06:26 PM
Tmurph2960 Tmurph2960 is offline
LawnSite Member
 
Join Date: Oct 2012
Posts: 10
.004 to .006. You will need a hex wrench set, feeler gauge, and a socket set. Turn the engine over until you have it at top dead center. Both valves should be closed and the piston at the top of its stroke. Check your gap then and if it is greater than .006 then adjust.
Reply With Quote
  #16  
Old 11-20-2012, 06:50 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,008
Quote:
Originally Posted by Tmurph2960 View Post
.004 to .006. You will need a hex wrench set, feeler gauge, and a socket set. Turn the engine over until you have it at top dead center. Both valves should be closed and the piston at the top of its stroke. Check your gap then and if it is greater than .006 then adjust.
Murph....you're a little confused....FB460 engines are different than FC420's....
You have to remove the head and remove the valves....then grind the valve stems to get your clearances on the FB460.
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
  #17  
Old 11-24-2012, 09:56 PM
Tmurph2960 Tmurph2960 is offline
LawnSite Member
 
Join Date: Oct 2012
Posts: 10
Well, lets see..... this morning it was 18 and my my mower started without starting fuiled. it never has until I adjusted my valves and used 5w30oil.... so I think that I will stick with what i AM DOING.....
Reply With Quote
  #18  
Old 11-24-2012, 10:28 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,008
Quote:
Originally Posted by Tmurph2960 View Post
Well, lets see..... this morning it was 18 and my my mower started without starting fuiled. it never has until I adjusted my valves and used 5w30oil.... so I think that I will stick with what i AM DOING.....
Tmurph....I don't care if you woke up and you were 118.....
You adjusted the valves on your FC420. 14hp engine...with an adjustable valve train..
You just instructed the OP to perform the same procedure on an FB460 12 1/2hp engine..
Valve adjustments on the FB460 can only be made by removing the valves and grinding the stems.
Kinda like trying to install windows xp pro on a smartphone...ain't gonna happen...
I think I will stick with what I am doing too......
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
  #19  
Old 11-24-2012, 11:29 PM
Darryl G Darryl G is offline
LawnSite Fanatic
 
Join Date: May 2001
Posts: 7,980
Yeah, both my 17 and 23 Kawi engines are hard to start for the first time in the morning. The guys are right on about the choke...it needs to be closed 100%. I use a jumper pack on mine this time of year with overnight freezing temps, even though the batteries are good. They're pretty small batteries and trying to turn over the engine and hydros they turn over kind of slow. With the jumper pack on they fire a lot quicker. Never used starter fluid on them either.
Reply With Quote
  #20  
Old 11-25-2012, 03:47 AM
44DCNF 44DCNF is offline
LawnSite Bronze Member
 
Join Date: Jul 2007
Location: Northern Illinois
Posts: 1,396
Roll the pull starts up into the compression stroke first, before pulling to start. Use a multi weight oil for fall/winter, preferably synthetic, but watch for greater consumption. Synch the choke/throttle. As the throttle cable and it's linkage plate wear, choke adjustments are required. Keep air and pre filter clean (from leaf season).
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 12:24 AM.

Page generated in 0.07871 seconds with 9 queries