Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #181  
Old 11-25-2012, 03:57 PM
44DCNF 44DCNF is offline
LawnSite Bronze Member
 
Join Date: Jul 2007
Location: Northern Illinois
Posts: 1,399
Quote:
Originally Posted by piston slapper View Post
Not sure where you are going with this.????
I am simply making a contribution to the thread, and since I don't have a picture handy, was just explaining the tools used......a punch of whatever size the job dictates to be used, and a pile of oil soaked bits of toweling or rag. I was going nowhere else with it, and am puzzled at your response.

What is it used for is my question posed to stump you or other participants. I guess maybe I have stumped, or confused you, at least.

Reply With Quote
  #182  
Old 11-25-2012, 04:11 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,027
Yeah...you confused me...figured you were countering my one inch punch....???
Inhaled too much migwire smoke this weekend....its all good...

You may stump me on this one too...
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
  #183  
Old 11-25-2012, 04:15 PM
Restrorob's Avatar
Restrorob Restrorob is offline
LawnSite Fanatic
 
Join Date: Apr 2005
Location: Show'n my truck off !
Posts: 10,694
Quote:
Originally Posted by 44DCNF View Post
What is it used for

I'll bite......

Pour the oil in the bowl, Mix the paper/oil with the punch until fully soaked. Then take the hammer and whack the center of the bowl.

Used to put oil spots all over the front of your shirt ?
__________________
Quote:
Originally Posted by piston slapper View Post
You never learn anything until you admit you don't know it all...

"Why go out preserved when you can go out beat up, worn out, sliding in sideways screaming, Holy Sh!t What A Ride" !!!
Reply With Quote
  #184  
Old 11-25-2012, 04:47 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,027
Looks like you are making packings for a blackpowder bb gun...???

Maybe prelubing threaded holes for easier assembly...???
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
  #185  
Old 11-25-2012, 05:08 PM
Patriot Services's Avatar
Patriot Services Patriot Services is online now
LawnSite Fanatic
 
Join Date: Jul 2006
Location: Tampa FL
Posts: 8,457
I checked the anarchists cookbook and all the past episodes of Doomsday Preppers and got nothing.
Posted via Mobile Device
Reply With Quote
  #186  
Old 11-25-2012, 05:33 PM
44DCNF 44DCNF is offline
LawnSite Bronze Member
 
Join Date: Jul 2007
Location: Northern Illinois
Posts: 1,399
LOL. It's used to hydraulically remove bushings or bearings from small blind holes. Such as in a starter or plow motor end cap, cam bearing, bushed shafts in gear mechanisms, needle bearings from ends of gear shafts, etc. Removing the bushing from a flywheel would be a larger example it could be used on if you were shy the proper blind hole puller.

Punch needs to fit closely the bore of the part being removed. Pack the hole with oil soaked wadding and tap the punch in. Pressure from behind drives the bushing or needle bearing cage out. Add more wadding as the part pushes out.
Reply With Quote
  #187  
Old 11-25-2012, 05:47 PM
Patriot Services's Avatar
Patriot Services Patriot Services is online now
LawnSite Fanatic
 
Join Date: Jul 2006
Location: Tampa FL
Posts: 8,457
Ok, I've used the same technique for getting pilot bushing out of cranks. Just not a tapered drift punch.
Posted via Mobile Device

Last edited by Patriot Services; 11-25-2012 at 05:54 PM.
Reply With Quote
  #188  
Old 11-25-2012, 05:50 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,027
The ole hydraulic punch...trick...have to add that to my portfolio...

Never did find a way to upload pics from my droid....
Guess it can wait till morning...stumps for everyone....
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
  #189  
Old 11-25-2012, 06:45 PM
BigFish's Avatar
BigFish BigFish is offline
LawnSite Bronze Member
 
Join Date: Jul 2008
Location: chesapeake, va
Posts: 1,634
Quote:
Originally Posted by Patriot Services View Post
Ok, I've used the same technique for getting pilot bushing out of cranks. Just not a tapered drift punch.
Posted via Mobile Device
Huh?? The punch in the pic ain't no tapered drift punch!

I've tried that trick, never had too much luck with it. Tried using grease, etc., finally broke down and bought a blind bushing puller.
__________________
" But let me tell you something ,folks: You can't fix stupid! There's not a pill you can take, there's not a class you can go to. Stupid is forever!"

......AMF!
Reply With Quote
  #190  
Old 11-25-2012, 07:10 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
 
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,027
I usually thread a tap into the bushing...when the tap hits the bottom of the hole it threads the bushing out..
__________________
If You Have All The Answers...Except The One You Need...You're Not Trying Hard Enough...
Do The Work
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 12:23 PM.

Page generated in 0.08244 seconds with 10 queries