Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #101  
Old 12-21-2011, 08:01 AM
carlriv's Avatar
carlriv carlriv is offline
LawnSite Member
 
Join Date: Dec 2001
Location: Mass
Posts: 99
BTW I dont have a wiring diagram... I assume you have the service manual, but I dont think the wiring is in here http://www.asvparts.com/Manufacturer...ice-Manual.pdf

I just cut the coil wires, spliced in an eylet on the ground side and bolted it directly to the frame. In the manual look for the pilot control maniflold page 3-2.
Reply With Quote
  #102  
Old 12-21-2011, 08:29 PM
kgserv's Avatar
kgserv kgserv is offline
LawnSite Member
 
Join Date: Mar 2011
Location: altoona pa
Posts: 104
i remember they did have to pull the seat and stuff for mine, i bridged all of my swithces to and it still didnt move
Reply With Quote
  #103  
Old 12-21-2011, 09:33 PM
Stony Bob Stony Bob is offline
LawnSite Member
 
Join Date: Feb 2011
Location: stony mountain manitoba
Posts: 22
Maybe?

What about causes #4 or 8 in the service manual troubleshooting section 15-2.


Problem 3

Machine starts but hydraulics will not operate.
Probable cause

1. Lap bar must be in down position, operator must be
seated in seat, and front door (if installed) must be
closed.
2. Safety fuse blown.
3. Faulty operator presence switch.
a) Test continuity through seat, lap bar, and door
switch. Adjust or replace as necessary. Lap bar
and door switch are magnetic switches and
should be adjusted to approximately 1/16 inch
away from steel pickup bracket.

4. Poor ground (check ground wires on bottom left rear
side of hydraulic reservoir).


5. Safety relay is not activating.
6. Faulty safety solenoid or safety solenoid spool.
7. Poor wire connections on fuse, relay, or safety solenoid.

8. Low charge pressure.
Reply With Quote
  #104  
Old 12-22-2011, 03:14 AM
greyim greyim is offline
LawnSite Member
 
Join Date: Mar 2010
Location: Tas Australia
Posts: 33
Yes, working thru the list..
Earths - checked and tested ok (awkward place!)
bridging the seat and bar switches at their plugs - no diff..
Replaced safety relay with new...
Next thing, will try the solenoids... bit hard to get at, will take the seat off...

Meantime, tired of driving out to site,
have recovered it back home.
Alot of work for a wire untight!
Perhaps I should abandon it alone?
Did I mention it's hot here?
Better than cold sleet and snow..
feelin better after a beer....
getting ready for another go
Reply With Quote
  #105  
Old 12-22-2011, 01:13 PM
carlriv's Avatar
carlriv carlriv is offline
LawnSite Member
 
Join Date: Dec 2001
Location: Mass
Posts: 99
I'm not sure removing the seat will help. Wire up a new coil to a 12V source and try to move it with that in place (bypass everything). If you get it to move that way put it up on some blocks or a lift, and lock the loader arms up... Much better access.
Reply With Quote
  #106  
Old 01-04-2012, 04:17 PM
greyim greyim is offline
LawnSite Member
 
Join Date: Mar 2010
Location: Tas Australia
Posts: 33
safety circuit

So, turns out the safety solenoid is cooked.. got it out with a wrench
Attached Images
 
Reply With Quote
  #107  
Old 01-04-2012, 06:22 PM
swanny swanny is online now
LawnSite Senior Member
 
Join Date: Jan 2009
Location: mt. airy maryland
Posts: 549
http://www.ebay.com/itm/167-0024-CHA...item19cc12fabd

a good deal on a drive motor.
Reply With Quote
  #108  
Old 03-16-2012, 05:56 PM
greyim greyim is offline
LawnSite Member
 
Join Date: Mar 2010
Location: Tas Australia
Posts: 33
Yawn

Another bites the dust
Attached Images
 
Reply With Quote
  #109  
Old 04-15-2013, 07:03 PM
merbesfield merbesfield is offline
LawnSite Member
 
Join Date: Mar 2013
Location: Atlanta
Posts: 9
pump source

Just wondering if anyone has found a good source for these pumps lately? Our RC30 is down. Thanks
Reply With Quote
  #110  
Old 04-15-2013, 09:12 PM
Hollowellreid Hollowellreid is offline
LawnSite Member
 
Join Date: Aug 2008
Location: Ann Arbor, Michigan
Posts: 224
Which pump?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 06:49 PM.

Page generated in 0.09438 seconds with 10 queries