Register free!

The Green Industry's Resource Center



Reply
 
Thread Tools   Display Modes
  #1  
Old 05-19-2013, 07:48 AM
Signature Landscaping1's Avatar
Signature Landscaping1 Signature Landscaping1 is offline
LawnSite Bronze Member
 
Join Date: Nov 2005
Location: Mass
Posts: 1,499
Wright Stander Aerocore deck, best blades?

Hi there, I bought a brand new wright stander last spring with the fixed aero core deck.It now has 297hrs. I still like the old deck on the standers way better. I have an older 36 stander that is having no problems cutting. Now my issue is I cannot seem to find a good blade and i have been getting terrible cutting results. Im still getting shaggy results. I had been using the stens rapture mulching blades in the fall, which were great but didnt have much suction. I have scag blades on it now and it cuts terrible. I cannot seem to get it to give a good cut like the old deck. I wanted to do a high lift.

Any suggestions?

Thanks
Joe
__________________
Joe
Reply With Quote
  #2  
Old 05-20-2013, 08:14 AM
kawakx125 kawakx125 is offline
LawnSite Senior Member
 
Join Date: Apr 2012
Location: lees summit, mo
Posts: 945
what scag blades do you have? i run the 482878 and get a good cut, also like the gator g5 blades. i'm afraid to run a high lift blade like the 482711 for fear of making the clumping issue worse
Reply With Quote
  #3  
Old 06-17-2013, 12:34 PM
mmerder mmerder is offline
LawnSite Member
 
Join Date: Jun 2013
Location: Huntingburg, IN
Posts: 18
Are you not using Wright blades becuase of cost? Try to match up to an Oregon blade. Oregon makes Wright's blades for them anyway.
Reply With Quote
  #4  
Old 06-17-2013, 10:20 PM
kawakx125 kawakx125 is offline
LawnSite Senior Member
 
Join Date: Apr 2012
Location: lees summit, mo
Posts: 945
i'm not using wrights blades because they suck even worse than anything else.
Reply With Quote
  #5  
Old 06-18-2013, 12:12 AM
weve weve is offline
LawnSite Senior Member
 
Join Date: Dec 1999
Location: Central Illinois
Posts: 376
I purchased a new Stander X with 52" Aerocore deck in March. The factory blades were Oregon fusion with only the Wright part number (71440009) stamped on them. They have a half inch offset with notched foil.

I am also using Oregon 93-010 which is listed as a Bob-Cat blade. It is not a Fusion blade and does not have the notched foil. They are an offset blade.

Both of these blades do a good job for me.

I have the Oregon G5 596-344 blades too. They did not do well this spring with the heavy rains that we got. I will try them again soon.
__________________
Dixie Chopper XWD3500-60 - Wright Stander X - Echo SRM 2100SB - Echo PAS-260
Echo PB-650T - Echo PB-770T - Echo HC-1500 - Shindaiwa T2500 - Shindaiwa PB270 - Shindaiwa PS344
Reply With Quote
  #6  
Old 11-22-2014, 11:48 PM
fobaum fobaum is offline
LawnSite Senior Member
 
Join Date: Aug 2008
Location: Ft lauderdale, Florida
Posts: 321
Anybody find the right blades for the aerocore?
__________________
Expert lawn maintenance & landscaping LLC.
2015 f350 6.7 green gem/caribou lariat
2012 f350 6.7L Ultimate lariat traded
2008 tundra 5.7 d-cab -sold-
1998 isuzu diesel dump 14,500gvw
2011 grandstand 60''
2013 grandstand 36''
2014 JD 652R EFI quik trac
Reply With Quote
  #7  
Old 11-23-2014, 12:07 AM
turfbuilder's Avatar
turfbuilder turfbuilder is offline
LawnSite Senior Member
 
Join Date: Mar 2009
Location: New Red State, USA
Posts: 468
The high lift fusions worked well for us as well as Oregon high lifts and G6 gators. Been running Wrights since the 90's when they 1st came out and my opinion is the Aerocore deck is better than their previous decks.
Reply With Quote
  #8  
Old 11-23-2014, 05:06 PM
STATEMENTLAWNCARE STATEMENTLAWNCARE is online now
LawnSite Member
 
Join Date: Apr 2012
Location: Orono, Mn
Posts: 98
SCAG blades 482878 worked best for me. Do you have the proper pitch on your deck? Correct tire pressure?
Posted via Mobile Device
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 10:35 AM.

Page generated in 0.07162 seconds with 9 queries