Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #1  
Old 03-06-2007, 07:24 PM
ScottsQLS ScottsQLS is offline
LawnSite Member
 
Join Date: Nov 2006
Location: Plymouth, Minnesota
Posts: 41
Putting Brakes on a Single Axle

i was wondering if there is anyone out there that has ever tryed to put or that has put brakes on to a single axle trailer? i have a 6.5 x 12 trailer and it sometimes gets to the point where when i have to slamed on the brakes that i can really feel it, so i was thinking about putting some brakes on the trailer.

just wondering if its a hard job or if its a pretty easy do it yourself job?
is there any kits out there that i can use?

if anyone could help me out with this that would be great, thanks guys
__________________
1996 Ford F-150
757 60" John Deere
727 54" John Deere
36" metro
6 x 12 Trailer
Aerator
Power rake
Reply With Quote
  #2  
Old 03-06-2007, 07:51 PM
muddstopper's Avatar
muddstopper muddstopper is offline
LawnSite Silver Member
 
Join Date: Dec 2002
Location: transition zone
Posts: 2,343
Piece of cake. if you can pull the hubs and grease repack bearing, you can put on new set of hubs and brakes. 4 bolts in the backing plate that bolt to the axle. You will need to make sure your axle already has the flange welded on it to accept the brake backing plate. Wireing is simple, two wires, one ground and one hot, doesnt matter which you choose to make a ground, it will work either way. You will need to wire in a brake controller inside the truck. Directions come with the controller and are simple and easy to follow.
Reply With Quote
  #3  
Old 03-06-2007, 08:10 PM
mattfromNY mattfromNY is offline
LawnSite Bronze Member
 
Join Date: Jan 2006
Location: Central NY
Posts: 1,580
I have a PJ 6.5x 10 single axle trailer that came with a 3500 lb. brake axle. It only cost me $1200 new. I love having the brakes, I carry my Ferris IS2000 and Ferris 36" walker in the summer, and my Massey GC2300 tractor/ snowblower in the winter. The brakes have saved my a$$ several times on wet and snowy roads! I would never go back to a trailer w/out brakes.
Reply With Quote
  #4  
Old 03-06-2007, 08:34 PM
Tadams's Avatar
Tadams Tadams is offline
LawnSite Senior Member
 
Join Date: Sep 2002
Location: Cartersville, GA
Posts: 790
You should be able to buy everything that you need at Northern Tool to put brakes on your trailer.
__________________
TODD

You don't stop playing because you get old, you get old because you stop playing.
Reply With Quote
  #5  
Old 03-06-2007, 08:37 PM
Jason Rose's Avatar
Jason Rose Jason Rose is offline
LawnSite Fanatic
 
Join Date: Jan 2003
Location: Hutchinson, Kansas
Posts: 5,775
When you price the brake hubs and drums for this axle also price a whole new axle with brakes already installed. To buy them seperate and install them is usually about the same price as a whole new, preassembled axle! Iv'e searched and searched and found this to be the case most of the time, and I'm talking 5 to 10 bucks here difference at the most.

WIring is "somewhat" easy. The brake controler has to go in the cab of the truck, wires run through the firewall and one wire hooks to your corresponding brake pedal sensor wire. You will be advised to run a 12 gauge wire for the hot lead, from the battery all the way to the plug. Granted, you only have one axle, but this will ensure it works right for multi axle trailers too. If you don't have a 6 round of 7 round RV type plug on the truck/trailer you will need one of them. If you have a "newer" truck, many are prewired for brake controlers and all you have to do is plug and play. You will need your factory wiring harness or you can usually buy one that fits your make/model truck for around $20.

Overall you are looking to spend $350 to $400 tops for the setup.

For your application the "Voyager" controler would be quite suffuicient, you could get better though if you want too spend the money. (I ordered my controler from this site, they were about the cheapest I found + free shipping on the high end controlers http://www.brakecontroller.com/

I also ordered brakes from: http://shop.easternmarine.com/
Best prices I could find anywhere, local guy said the price I got from this site was less than his COST. I wouldn't order a whole axle online though, I'd imigine shipping would be a killer...
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 06:39 AM.

Page generated in 0.07869 seconds with 7 queries