Register free!

The Green Industry's Resource Center



Reply
 
Thread Tools   Display Modes
  #91  
Old 08-19-2012, 01:32 PM
fumblefingers fumblefingers is offline
LawnSite Member
 
Join Date: Aug 2012
Location: Geneva, Fl
Posts: 55
I want to set the throttle lever in the proper position. Please put your mower in the run position and let me know where the 8mm linkage nut is in in the slide position. The nut I am referring to is best seen in picture 1
Reply With Quote
  #92  
Old 08-19-2012, 02:05 PM
fumblefingers fumblefingers is offline
LawnSite Member
 
Join Date: Aug 2012
Location: Geneva, Fl
Posts: 55
Mower pix

Top view with air filter out
Reply With Quote
  #93  
Old 08-19-2012, 03:35 PM
cs9530 cs9530 is offline
LawnSite Member
 
Join Date: Jul 2009
Location: Fairfax, VA
Posts: 12
Quote:
Originally Posted by fumblefingers View Post
I would like to have pages S 93 and S 105 if it would not be too much trouble.
Thanks
Here are pages 93 and 105 - hope this helps...
Attached Images
File Type: pdf Kubota SM - Pg 93 and 105.pdf.pdf (112.5 KB, 95 views)
Reply With Quote
  #94  
Old 08-19-2012, 03:58 PM
fumblefingers fumblefingers is offline
LawnSite Member
 
Join Date: Aug 2012
Location: Geneva, Fl
Posts: 55
Quote:
Originally Posted by cs9530 View Post
Here are pages 93 and 105 - hope this helps...
Thanks a lot. I also see page 51 is mentioned about the blade clutch. Could you add.
Reply With Quote
  #95  
Old 08-19-2012, 04:02 PM
treysoucie's Avatar
treysoucie treysoucie is offline
LawnSite Member
 
Join Date: Aug 2012
Location: houston
Posts: 111
OK I'll snap a pic of the linkage in choke, low throttle and high throttle
Posted via Mobile Device
Reply With Quote
  #96  
Old 08-19-2012, 04:05 PM
treysoucie's Avatar
treysoucie treysoucie is offline
LawnSite Member
 
Join Date: Aug 2012
Location: houston
Posts: 111
My non self propelled bogs down and dies if I apply the clutch too fast. If I apply the clutch very slowly it stays running. I may need to rip the clutch apart and check for corrosion or improper bearing wear
Posted via Mobile Device
Reply With Quote
  #97  
Old 08-19-2012, 04:25 PM
fumblefingers fumblefingers is offline
LawnSite Member
 
Join Date: Aug 2012
Location: Geneva, Fl
Posts: 55
I pulled the carb and cleaned again. This time I pulled the pilot jet and sprayed the hell out of it because I did not have a tiny wire. Then I put carb back, put the throttle in run and pulled the starter. the mower started and ran for15 seconds then ran out of gas (empty tank):0
It is too ot to mess with this any more today
Reply With Quote
  #98  
Old 08-19-2012, 04:26 PM
cs9530 cs9530 is offline
LawnSite Member
 
Join Date: Jul 2009
Location: Fairfax, VA
Posts: 12
Quote:
Originally Posted by fumblefingers View Post
Thanks a lot. I also see page 51 is mentioned about the blade clutch. Could you add.
Here's page 51.
Attached Images
File Type: pdf Kubota SM - Page 51.pdf.pdf (60.6 KB, 86 views)
Reply With Quote
  #99  
Old 08-19-2012, 04:35 PM
treysoucie's Avatar
treysoucie treysoucie is offline
LawnSite Member
 
Join Date: Aug 2012
Location: houston
Posts: 111
Sounds promising. Usually when people have starting and idling issues 9times out of ten it's the pilot that's gunked up.
Posted via Mobile Device
Reply With Quote
  #100  
Old 08-19-2012, 07:58 PM
cs9530 cs9530 is offline
LawnSite Member
 
Join Date: Jul 2009
Location: Fairfax, VA
Posts: 12
Quote:
Originally Posted by cs9530 View Post
Here's page 51.
Here's the S.2 Mower Blade Clutch and Blade (all three pages).
Attached Images
File Type: pdf Kubota W5021 Shop Manual Mower Blade Clutch and Blade.pdf (175.9 KB, 91 views)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 06:55 PM.

Page generated in 0.07271 seconds with 8 queries