search sponsored by:
Advanced Search

The Green Industry's Resource Center

Old 04-03-2010, 04:08 PM
Young's Lawn Service LLC Young's Lawn Service LLC is offline
LawnSite Member
Join Date: Oct 2006
Location: Mount Orab, Ohio
Posts: 56

I have an exmark laser with a 1 year old motor. Battery keeps going dead. I put a new battery on yesterday and it did fine. Today it has started doing the same thing. The battery is not charging I assume? I shut it off to talk to my customer and would not restart. I jumped it and started and ran fine for a bit then just died like I was out of gas. Jumped it again... started fine.
Any suggestions?
I'm thinking maybe the stater?
Is there anything else it could be?

Any help would be great.
Reply With Quote
Old 04-03-2010, 04:47 PM
betmr betmr is offline
LawnSite Bronze Member
Join Date: Mar 2009
Location: Piscataway, NJ
Posts: 1,663
How about corrosion, are the battery terminals good and clean? Look for loose, or corroded wires, and terminals.
Reply With Quote
Old 04-03-2010, 04:54 PM
Crash's Avatar
Crash Crash is offline
LawnSite Member
Join Date: Mar 2009
Location: Mid Michigan
Posts: 192
Do you own a multimeter? If not go and get one. Check all your powers and grounds, do voltage drops, this will tell you where your problem is.

"We Want to Make You Look Good"

Kyle Sanborn
Director of Operations


Fully Insured
Free Estimates
Residential & Commercial
Reply With Quote
Old 04-05-2010, 12:41 PM
piston slapper's Avatar
piston slapper piston slapper is offline
LawnSite Platinum Member
Join Date: Mar 2010
Location: Tampa Fl
Posts: 4,213
Check your fuses. Lazers usually have 2 fuses, 1 for the ignition and 1 for the charge system.If I knew which engine you had , it might be easier to diagnos.
Reply With Quote
Old 04-05-2010, 03:32 PM
dutch1's Avatar
dutch1 dutch1 is online now
LawnSite Silver Member
Join Date: Dec 2004
Location: Jayhawk
Posts: 2,222
Using your volt ohmeter, check the battery voltage with the key off. Start the engine then check the voltage at the battery posts. If you have a voltage drop then you likely have a charging coil that is defective or a rectifier/regulator that is bad. You could also check the output from the charging coil by disconnecting the connectors where the two wires come from the charging coil. You didn't mention what engine you have but normally the output from the coil will be any where from 40-70 volts AC.
Reply With Quote
Old 04-06-2010, 09:00 PM
fixer67's Avatar
fixer67 fixer67 is offline
LawnSite Silver Member
Join Date: Apr 2004
Location: Tryon NC
Posts: 2,161
Model numbers of the engine and the machine it is on would go a long way in helping you.
Reply With Quote
Old 04-12-2010, 09:22 PM
Young's Lawn Service LLC Young's Lawn Service LLC is offline
LawnSite Member
Join Date: Oct 2006
Location: Mount Orab, Ohio
Posts: 56
Its a Kohler CH-730. I found 2 fuses behind the front panel. The one that has 3 wires going into it is melted. So melted that the fuse will not come out. Is this the one for the charging system? Looks like it has been like that for a while?
I tested the battery and its almost at 13 volts when just sitting there, it drops below 12 when the engine is on and about the same when I engage the blades. Its been lasting about 4 hours, so I've been coming home for lunch and re-charging until I get this resolved.
I hate electrical problems!
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Layout Style:

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 03:24 AM.

Page generated in 0.08264 seconds with 10 queries