Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #1  
Old 07-17-2002, 07:09 PM
Clayton800 Clayton800 is offline
LawnSite Member
 
Join Date: Jul 2002
Location: Nashville, TN
Posts: 28
HELP My Shindaiwa wont edge!

Hey Guys,
Have a problem here, and hope you might have some suggestions. I use a few Shindaiwa t270's and two of them, when I flip them over to edge with, they run terrible. They have no power and just wont tackle the job. However, when running them right side up, they run great! but as soon as I flip the unit over it sputters.

now, I went through each of them, cleaned out the carb, muffler, exaust port, changed the fuel filters, messed with the carb adjustment screw, all of wich yielded no improvements. I also run the shindaiwa oil in the mix. I took off the spark arrestor, and installed a new NKG spark plug.

Any one ever had this problem before? I cant figure it out. Both units are under a year old, I would take them in for service but the dealer here is so slow, he should have done by Christmas.

Any suggestions? HELP


Thanks

Bryan

Last edited by Clayton800; 07-17-2002 at 07:19 PM.
Reply With Quote
  #2  
Old 07-17-2002, 09:04 PM
General Grounds General Grounds is offline
LawnSite Senior Member
 
Join Date: Jan 2001
Location: Manalapan,nj
Posts: 902
:blob3: ummm, nver had that problem usually turn them upside down to clear them out when we first start them in the morning, the only thing i can think of is that you have a problem with the gas caps. tony
Reply With Quote
  #3  
Old 07-18-2002, 03:50 AM
Flyrod Flyrod is offline
LawnSite Member
 
Join Date: Jun 2002
Location: Elizaville, NY
Posts: 9
It's time for a carb rebuild.
Reply With Quote
  #4  
Old 07-18-2002, 07:20 PM
grasmo grasmo is offline
LawnSite Member
 
Join Date: Jun 2002
Location: fl
Posts: 34
try bending the float/fuel pump tang up a little.
Reply With Quote
  #5  
Old 07-21-2002, 10:36 AM
Fish's Avatar
Fish Fish is offline
LawnSite Member
 
Join Date: Feb 2001
Location: Lawrenceburg, KY
Posts: 139
The fuel pickup lines may need replaced. When you turn the
trimmer on its side, the cracks/holes in the lines are above the fuel level and sucking air.
Fish
Reply With Quote
  #6  
Old 07-22-2002, 11:02 PM
TFL TFL is offline
LawnSite Member
 
Join Date: Mar 2001
Location: Mt. Pleasant TX
Posts: 210
My old JDXT120 did that i tryed to find the problem but couldn't Finnally decided it my be time for a new one

If the carb rebuild works tell me it will mak a great backup.
Reply With Quote
  #7  
Old 07-23-2002, 08:42 AM
khouse khouse is offline
LawnSite Bronze Member
 
Join Date: Feb 2001
Location: lee's summit, mo
Posts: 1,479
make sure when you flip it over your fuel pick up/filter is following the fuel.
Reply With Quote
  #8  
Old 08-01-2002, 05:25 PM
metrognome metrognome is offline
LawnSite Member
 
Join Date: Mar 2002
Location: Portland, OR
Posts: 3
look at the inlet control lever for a "divot" at the contact point where the diaphragm button touches it.
several of our customers have experienced this problem but couldn't wait to have us run it through the shop and just loosened the clamp that holds the power unit to the shaft tube and turned the engine so it was "right side up" when edging. Seems to work until they can leave it for carb rebuild ;o)

metrognome
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 03:21 PM.

Page generated in 0.08549 seconds with 7 queries