Register free!
Search
 
     

The Green Industry's Resource Center


Click for Weather
Reply
 
Thread Tools Display Modes
  #1  
Old 12-20-2011, 06:42 PM
racer1970 racer1970 is offline
LawnSite Member
 
Join Date: Dec 2011
Location: Apopka Fl
Posts: 6
Carb. tuning on Echo HC-150

Would anyone know what the factory setting is for the one hi-mixture adj. screw is in number of turns out is? As when I got this HC150 it was running vary rich, black plug, oil dripping out of the muffler etc. I turned the Hi speed adj screw in a few turns and runs accelerates much better and can idle forever if I let it.... but with non-eth 93octane fuel and Amsoil Saber mixed to 80:1 it really screams at wide open throttle but still smokes? so I would like to know if possible the factory setting of the Hi speed screw located by the primmer bulb. As i would like to tune this right and correct.

Thank you in advance for your help and input
Reply With Quote
  #2  
Old 12-20-2011, 07:49 PM
djagusch djagusch is online now
LawnSite Gold Member
 
Join Date: Mar 2006
Location: MN
Posts: 3,414
Just a thought. Have you cleaned the exhaust port (and muffler) out and put in a new plug? The oil from being rich takes awhile to burn off before it quits smoking.

I don't know the standard turn out. I always go by how it sounds/runs. After that check the plug after running it and see what it looks like.
__________________
Looking for blown Kawi 29HP DFI engine's fd791d, whole thing, intake, throttle body, and electronic's. PM me if you have something you would like to sell.
Reply With Quote
  #3  
Old 12-20-2011, 09:35 PM
GlynnC GlynnC is offline
LawnSite Senior Member
 
Join Date: Sep 2009
Location: Nashville Tennessee
Posts: 469
Factory settings are not always correct--one of the most accepted ways to tune the hi-speed is: 1. run the engine to get to operating temp. 2. With engine running at full throttle, close (clockwise) the hi-speed screw until engine speed starts to slow down, keep count of how much you turn the screw and open it (counter-clockwise) until engine starts slowing down, then set the screw half-way in-between the two points.

For years I tuned by setting to highest rpm position. I think this is now too lean--especially with today's gasoline. Open a little past this point.
Reply With Quote
  #4  
Old 12-21-2011, 10:44 AM
BigFish's Avatar
BigFish BigFish is offline
LawnSite Bronze Member
 
Join Date: Jul 2008
Location: chesapeake, va
Posts: 1,607
GlynnC's advice is pretty much on the money. You don't want to lean it out too much ( max screaming rpm) or ya risk a meltdown! And with clippers ya got all that stuff movin around in there.

The " factory setting " that you are referring to is actually just the starting point to get it running. In your case it does'nt matter since it already runs.
It usually is 1-1/2 to 2 turns out from lightly seated.
__________________
" But let me tell you something ,folks: You can't fix stupid! There's not a pill you can take, there's not a class you can go to. Stupid is forever!"

......AMF!
Reply With Quote
  #5  
Old 12-30-2011, 01:22 PM
Big Wes Big Wes is offline
LawnSite Member
 
Join Date: Sep 2004
Location: Virgina Beach,Virginia
Posts: 247
From the closed/seated position, open the H & L jets 1 full turn. Should start from there.
__________________
Big Wes Owner/Operator Neighborhood Lawn Care. Since 1990
"Satisfaction Guaranteed or Double Your Clippings Back"
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 11:09 PM.

Page generated in 0.07393 seconds with 7 queries