|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#1
07-31-2012, 08:20 PM
|
|||
|
|||
|
Walker mower cutting like crap
I have a walker 20hp MTGHS it's just doesn't seem to be cutting right, checked rpms they are good, blades are good, deck and ports are cleaned, both gear boxes are new, blades are on right, tire pressure is good, using the walker pins and shims for the deck, all holes are the same, blower fan doesn't looked too chewed up, screen is clean. Replaced PTO belt and pretty sure i have the tension right, it just seems to be laying a lot of grass down instead of cutting it I've searched the forum and can't seem to find anything I haven't checked so I'm looking for some other suggestions if anyone has them. I haven't had this issue with any of my other walkers and I'm at a loss now
__________________
2001 f350 diesel dually 2004 silverado 1500 4x4 2002 silverado 2500 4x4 2001 case 1845c Gravely 152 ztr 2006 walker GHS 16ft landscape trailer 2012 6 ton dump trailer 2004 JDJ 7 ton dump trailer Little wonder leaf loader Toro proline and Honda 21's Toro 36" walkbehinds Stihl,echo,handhelds and saws Arctic snow plows and snow ex salters 
|
|
#2
07-31-2012, 08:29 PM
|
|||
|
|||
|
what deck? are you sure the blades are right? the 52in deck the blades go on opposite the 48
|
|
#3
07-31-2012, 08:31 PM
|
|||
|
|||
|
It's a 48 one vertical one horizontal
__________________
2001 f350 diesel dually 2004 silverado 1500 4x4 2002 silverado 2500 4x4 2001 case 1845c Gravely 152 ztr 2006 walker GHS 16ft landscape trailer 2012 6 ton dump trailer 2004 JDJ 7 ton dump trailer Little wonder leaf loader Toro proline and Honda 21's Toro 36" walkbehinds Stihl,echo,handhelds and saws Arctic snow plows and snow ex salters
|
|
#4
07-31-2012, 08:31 PM
|
|||
|
|||
|
I'm having a time with walker rite now to I have a new mt23 ghs and its been in shop bout 10 times for various resons but now to top it of cut quality sucks.
Posted via Mobile Device
|
|
#5
07-31-2012, 08:39 PM
|
|||
|
|||
|
Quote:
|
|
#6
07-31-2012, 09:00 PM
|
|||
|
|||
|
Yeah I double checked just now there on right.
Could it be the tension on the pto belt?
__________________
2001 f350 diesel dually 2004 silverado 1500 4x4 2002 silverado 2500 4x4 2001 case 1845c Gravely 152 ztr 2006 walker GHS 16ft landscape trailer 2012 6 ton dump trailer 2004 JDJ 7 ton dump trailer Little wonder leaf loader Toro proline and Honda 21's Toro 36" walkbehinds Stihl,echo,handhelds and saws Arctic snow plows and snow ex salters
|
|
#7
07-31-2012, 09:01 PM
|
|||
|
|||
|
not as long as blades are turning full speed. Should be able to listen and tell by the sound if you've run one enough
|
|
#8
07-31-2012, 09:02 PM
|
|||
|
|||
|
the belt that runs the blower isn't broke is it?
|
|
#9
07-31-2012, 09:04 PM
|
|||
|
|||
|
I'm getting same prob I'm running 3750rpm new blower and belt and it still leaves hangers and has very little lift when cutting.
Posted via Mobile Device
|
|
#10
07-31-2012, 09:18 PM
|
|||
|
|||
|
Yeah it sounds fine I've run then for a bit that's why it's bugging me that I'm stumped. The for the blower is good plus it's still sucking clippings and leaves just not the cut the machine and other walkers have previously had
Posted via Mobile Device
|
 |
| Bookmarks |
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
