search sponsored by:
Advanced Search

The Green Industry's Resource Center

Old 05-01-2013, 08:53 PM
Ml504 Ml504 is offline
LawnSite Member
Join Date: May 2013
Location: Baton Rouge, LA
Posts: 4
2011 Ferris IS2000Z Clutch Problem

Hoping someone can offer some help on this issue. As the title states I have a 2011 Ferris IS2000Z with the 27hp Kawasaki and 52 inch cut. I have had the mower since new and this is the third time this clutch issue has arised. Here is the summary:

1. First time I took mower in for service because pto stopped working. Diagnosed that one of the wires going into the clutch had burnt in two. This was at 20 hours.
2. Second time pto would turn off when bogging down in deeper grass. Diagnosed clutch was bad and replaced entire assembly under warranty. This was at 45 hours.
3. Here I am now the pto has stopped working again and I looked and sure enough the positive wire going into the connector on the clutch has broke or burned off.

With all this said the mower has 75 hours on it and is now outside of the two year warranty. I need some suggestions on what to do or check. I have started looking for a bad ground but have not found anything. I'm hesitant to patch the wire and start running it because there is an underlying problem here somewhere that keeps getting overlooked.

Any suggestions are greatly appreciated!
Reply With Quote
Old 05-02-2013, 07:22 PM
Restrorob's Avatar
Restrorob Restrorob is offline
LawnSite Fanatic
Join Date: Apr 2005
Location: Show'n my truck off !
Posts: 11,004

Check the torque on the clutch mount bolt, It's possible to over tighten one and cause binding which can burn wires and the clutch up.

Torque should be 65-70 ft.lbs......
Originally Posted by piston slapper View Post
You never learn anything until you admit you don't know it all...
Originally Posted by MannsLawnService View Post
some times the man in my mirror isn't so smart...
"Why go out preserved when you can go out beat up, worn out, sliding in sideways screaming, Holy Sh!t What A Ride" !!!
Reply With Quote
Old 05-02-2013, 08:02 PM
greenology's Avatar
greenology greenology is offline
LawnSite Senior Member
Join Date: Oct 2012
Location: Sydney, Australia
Posts: 816
I saw an is2500 brand new 2 days ago having the exact same problem as this! Whenever cutting into thick grass the PTO would cut off. Dont know what the problem was but sounds like could be the same wire problem your having.

I shrugged it off thinking it would be an isolated problem, but sounds like its more common than I thought.

Mate I would take it back to your dealer & they should honour this under warranty, how far out of warranty is it? You would also have a guarentee on the workman ship of the dealer, they should have fixed it the first time, so now your having the same problem its up to them to fix it. Make a point when dropping it off that you wont be paying...
Reply With Quote
Old 05-02-2013, 08:04 PM
greenology's Avatar
greenology greenology is offline
LawnSite Senior Member
Join Date: Oct 2012
Location: Sydney, Australia
Posts: 816
Being that you had this same problem during your warranty period, it doesnt matter that the warranty has lapst. You wont have to pay for it, so def consider taking it back and having them fix it properly this time! goodluck
Reply With Quote
Old 05-03-2013, 07:05 PM
Ml504 Ml504 is offline
LawnSite Member
Join Date: May 2013
Location: Baton Rouge, LA
Posts: 4
Thank you for the advice.
Reply With Quote
Old 05-03-2013, 08:00 PM
Blade Runners's Avatar
Blade Runners Blade Runners is online now
LawnSite Bronze Member
Join Date: Apr 2012
Location: Woodlawn, TN
Posts: 1,016
Is the wire broken or is it burned off? This will help diagnose what the actual problem is. If the coating is burned along a length of the wire, it has been shorted somewhere for a length of time under heavy amperage load or the wiring is too small for the load to begin with. I would assume the wire is the correct size since it is factory. The blades/PTO disengaging makes me think there is an issue with the clutch itself or the air gap adjustment and is causing the wire to burn.

Is the shop checking the air gap on the clutch when they install it? Are they checking to make sure the wiring is not shorting out at the connection points and that it has enough slack that it isn't being stretched when the deck is engaged? I would be questioning what the shop is doing because they obviously haven't ID'd the cause and are just changing out parts.

Scag mowers
Blade Runners, LLC

"Always do your best. What you plant now, you will harvest later."
-Og Mandino
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Layout Style:

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 11:20 PM.

Page generated in 0.05896 seconds with 8 queries