Register free!
Search
 
     

Click for Weather
Reply
 
Thread Tools Display Modes
  #1  
Old 10-01-2013, 02:04 PM
ron mexico75's Avatar
ron mexico75 ron mexico75 is offline
LawnSite Bronze Member
 
Join Date: May 2009
Posts: 1,423
Spyker or Earthway?

I've had an Earthway for 2 years and began having issues with it about 2 months ago. The cotter pin that holds the drive wheel on keeps snapping in half. I went to Lowes and got the same size thinking the original was just old and had rusted out. Well, 3 more cotter pins have snapped in half. Finally called Earthway 2 weeks ago and explained my issue. Nice guy said it sounds like a gearbox issue and he was sending me a new one at no charge. Very good service if you ask me.

Well here it is (yesterday 9/30) and still nothing. I asked what carrier he sent it or if he had a tracking # etc. He said he wasn't sure, he just got in the office etc. but he would make sure that I got it. Sounds to me he forgot to send it out or the person he delegated that to never did it. Either way I'm slightly annoyed but not too much because they are replacing it for free.

Just got to thinking that maybe I should just buy a new one and keep this for backup. I mean, Earthway seems to be good and them sending a new gearbox out (albeit very slowly) I'm inclined to stick with them. However, I was looking at Spyker and they appear to be well built, have a nice website, include a cover with the spreader unlike Earthway and maybe it's just me, but by looking at the schematics of the spreader in the manual, seem to be a little bit better built.

I'm just very used to Earthway and also there spreader setting chart is no nonsense. I was looking online at the Spyker spreader chart and it seems very hazy to me. Maybe I just need to be educated or helped along in understanding it. As of right now, I'm leaning towards the Earthway out of familiarity with the spreader setting chart and kind of shying away from the Spyker for that reason only. That seems wrong to me. Anyone care to comment on the 2 as well as the setting chart.

I'm including a link to the models of each as well as the spreader chart so you can see exactly what I'm talking about.

Also, the Spyker is $352 cover included. The Earthway is $239 and cover is $25.50.


http://spyker.com/S40-5020-commercia...-spreader.html

(page 11 in link below for chart)

http://spyker.com/graphics/products/.../40_Series.pdf



http://www.earthway.com/products/mob...dcast-spreader

(page 2 in link below for chart)

http://www.earthway.com/wp-content/u...-tip-sheet.pdf
Reply With Quote
  #2  
Old 10-01-2013, 03:38 PM
ron mexico75's Avatar
ron mexico75 ron mexico75 is offline
LawnSite Bronze Member
 
Join Date: May 2009
Posts: 1,423
Wow does anyone have any input?
Reply With Quote
  #3  
Old 10-01-2013, 03:55 PM
gcbailey's Avatar
gcbailey gcbailey is offline
LawnSite Bronze Member
 
Join Date: Mar 2012
Location: southern WV
Posts: 1,762
I just recently purchased an Earthway 2150. I know it's not the best, but for just starting out I think it's worth the money. I have looked at a Lesco and it's by far built a lot better than the Earthway, but like I said, for the money I like the Earthway.

I agree with you on Earthway's chart. It's definitely good for your initial settings, but if I've been doing my math right, it's always about 1/1.5 less open than what I've been applying.
Reply With Quote
  #4  
Old 10-01-2013, 08:26 PM
jbturf jbturf is online now
LawnSite Bronze Member
 
Join Date: Sep 2007
Location: groton, MA
Posts: 1,298
I use cotter pins in all my spreaders also,
im sure the roll pins last a bit longer, but they can be a real bear to get
out. I bought a couple of cases of multi size cotter pins from harbor freight years ago and just keep it in the trailer.

trick is to use the largest size pin you can fit in the hole, if its sloppy at all it just prematurely wears and snaps

I end up replacing at least one every couple weeks, takes me all of about 60 seconds, im well trained lol
Reply With Quote
  #5  
Old 10-01-2013, 09:32 PM
Mike A Mike A is offline
LawnSite Member
 
Join Date: Aug 2013
Location: Evansville, in
Posts: 67
IMO Spyker makes the best spreader out there. I like their chart because it shows different sizes of granules and what setting to put it on for 1 lb - 6lb per 1000. Of course like it says, those are approx settings. U will need to calibrate it.
Lescos are good too.
Go with the Spyker, u won't be disappointed.
Posted via Mobile Device
Reply With Quote
  #6  
Old 10-01-2013, 09:41 PM
RigglePLC's Avatar
RigglePLC RigglePLC is online now
LawnSite Fanatic
 
Join Date: Jul 2006
Location: Grand Rapids MI
Posts: 9,268
I think the stainless steel Earthway has a better guarantee (5 years) and the no-grease wheel bearings are strong, with the bearing holder firmly welded to the frame. Spyker has the bearing holder not welded--but rather the tubing is just pounded flat and a plastic bushing to carry the axle is pressed in.

On worn spreaders the plastic wheel becomes slotted around the cotter pin on the drive wheel. It gets jerky when reversing. I thought everyone used a big nail instead of a cotter. Slide in; bend it.

Or if you decide to start over...I have a nice Scotts stainless steel commercial spreader, 80 pounds capacity. Retired--its for sale. Click my name and look at the pictures.

Last edited by RigglePLC; 10-01-2013 at 09:49 PM. Reason: add
Reply With Quote
  #7  
Old 10-02-2013, 09:02 AM
ron mexico75's Avatar
ron mexico75 ron mexico75 is offline
LawnSite Bronze Member
 
Join Date: May 2009
Posts: 1,423
Quote:
Originally Posted by Mike A View Post
IMO Spyker makes the best spreader out there. I like their chart because it shows different sizes of granules and what setting to put it on for 1 lb - 6lb per 1000. Of course like it says, those are approx settings. U will need to calibrate it.
Lescos are good too.
Go with the Spyker, u won't be disappointed.
Posted via Mobile Device
True, and I guess you could always figure it out, but, what about if you need more than 6 per 1000 such as seed for a new lawn? Isn't it easier like on the Earthway chart to know that the 50lb bag you bought covers 5-15,000 you just look at the chart and adjust accordingly? That's what's frustrating me unless someone can help me out.
Reply With Quote
  #8  
Old 10-02-2013, 09:05 AM
ron mexico75's Avatar
ron mexico75 ron mexico75 is offline
LawnSite Bronze Member
 
Join Date: May 2009
Posts: 1,423
Quote:
Originally Posted by RigglePLC View Post
I think the stainless steel Earthway has a better guarantee (5 years) and the no-grease wheel bearings are strong, with the bearing holder firmly welded to the frame. Spyker has the bearing holder not welded--but rather the tubing is just pounded flat and a plastic bushing to carry the axle is pressed in.

On worn spreaders the plastic wheel becomes slotted around the cotter pin on the drive wheel. It gets jerky when reversing. I thought everyone used a big nail instead of a cotter. Slide in; bend it.

Or if you decide to start over...I have a nice Scotts stainless steel commercial spreader, 80 pounds capacity. Retired--its for sale. Click my name and look at the pictures.
Maybe a nail would work. The hole is tiny though...1/8 inch. Maybe a finising trim nail? I guess that might be harder than a cotter pin.
Reply With Quote
  #9  
Old 10-02-2013, 09:09 AM
foreplease's Avatar
foreplease foreplease is offline
LawnSite Bronze Member
 
Join Date: May 2008
Location: St. Joseph, MI
Posts: 1,214
6#of seed is going to flow differently than 6# of fertilizer; just as different size fertilizers and different size seeds will not all flow at the same rate. Short answer for heavy seed application is go over it twice in different directions - something that is a good idea whether you are able to get enough down in one pass or not.
__________________
Michigan PABL
Reply With Quote
  #10  
Old 10-02-2013, 09:25 AM
ron mexico75's Avatar
ron mexico75 ron mexico75 is offline
LawnSite Bronze Member
 
Join Date: May 2009
Posts: 1,423
Quote:
Originally Posted by foreplease View Post
6#of seed is going to flow differently than 6# of fertilizer; just as different size fertilizers and different size seeds will not all flow at the same rate. Short answer for heavy seed application is go over it twice in different directions - something that is a good idea whether you are able to get enough down in one pass or not.
yeah that's true. So what type of spreader are you using?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.comô - Moose River Media
All times are GMT -4. The time now is 02:47 PM.

Page generated in 0.08196 seconds with 7 queries