Register free!

The Green Industry's Resource Center



Reply
 
Thread Tools   Display Modes
  #1  
Old 06-04-2006, 12:33 PM
efaubert1's Avatar
efaubert1 efaubert1 is offline
LawnSite Member
 
Join Date: Jul 2005
Location: Indiana
Posts: 109
Dixon cone adjustment???

Ok, my brother-in-law picked up a used Dixon 30" mower at an auction with a nice little 12hp Briggs for his small yard. It runs like a top, but it doesn't steer woth a darn. Now I have scoured the internet for cone adjustment, but it just isn't there. Amazing. Must be a million of these little mowers on the planet, yet how to adjust the drive must be the best kept repairman secret ever kept. So the question is, does anyone here know how to adjust them, and would you be willing to share the procedure please.
Reply With Quote
  #2  
Old 06-08-2006, 06:03 PM
mattrlang mattrlang is offline
LawnSite Member
 
Join Date: Sep 2005
Location: Missouri
Posts: 2
I too have spent countless hours searching for the same information. I have a Dixon 2301. I have found instructions for adjusting the original dixon standard transaxle, but mine has a z-drive transaxle (which, according to that information, differs from the standard in that it has swing-out levers and does not contain torque rods). The only technical information I've been able to find online is Dixon's application for a patent for the friction drives, but it didn't make it any more clearer. I had to replace a couple of broken pivot bolts on the rear of the cradles last summer and have been messing with it ever since trying to get it to drive right. But thus far I haven't broken the "code", I can't seem to adjust it so that there is enough torque going forwards and backwards. PLEASE, will someone knowledgable on these transaxles and adjustment procedures take the time to help those of us who are frustrated, sleepy (from staying up late searching online, chasing dead end links), and confused older Dixon owners.
Reply With Quote
  #3  
Old 06-08-2006, 07:36 PM
Restrorob's Avatar
Restrorob Restrorob is offline
LawnSite Fanatic
 
Join Date: Apr 2005
Location: Show'n my truck off !
Posts: 10,761
Well Guy's, Don't feel bad. I done a search the other night for about a hour and again just now for a hour. Looks like you are going to have to buy a service manual to find the adjustments you are looking for. I'm sure in your searches you have found manuals for sale but there are a couple here;
http://search.ebay.com/dixon-manual_...sopZ3QQxpufuZx that are priced pretty reasonable.

Good Luck
__________________
Quote:
Originally Posted by piston slapper View Post
You never learn anything until you admit you don't know it all...
Quote:
Originally Posted by MannsLawnService View Post
some times the man in my mirror isn't so smart...
"Why go out preserved when you can go out beat up, worn out, sliding in sideways screaming, Holy Sh!t What A Ride" !!!
Reply With Quote
  #4  
Old 10-24-2007, 11:05 AM
Bonycells Bonycells is offline
LawnSite Member
 
Join Date: Oct 2007
Location: Bailey, North Carolina
Posts: 1
Adjusting the original style Dixon Transaxle assembly

Standard Transaxle Adjustment Adjusting the Standard (Original) Dixon Transaxle

Pre-adjustment checks (Please note - all part numbers are in parentheses, quantities in bold.)

It will do no good to adjust the transmission if certain parts are worn excessively or broken.

Check these parts before proceeding.

1) All springs (6) (5133, 5170, 5036)

2) Rear pivot bolts(2) (2166) and hole (or bushing (5279) if so equipped).
These allow the rear of the cradle casting (holds the rotating discup in place) to pivot slightly as the control levers are moved.

3) Bell crank pivots (2) (kit 1636)
These connect the rod ends to the double ball joints.

4) Ball joints (4) and double ball joints (2) (8284, 8285, 3577)
The ball joints or rod ends as they are referred to connect the control levers to the transmission It is highly recommended to replace these with the newest style for longer wear and less play. A small amount of wear on a ball joint is multiplied several times at the control lever. If one side has a slight amount different wear than another, a perfectly adjusted transmission will not drive evenly due to lever play.

5) Torque rods (2) (5152, 5185, 2555, 2149)
These are the horizontal rods that extend through an eye bolt at the outside of the trans. These sometimes break near the point where they screw into the casting of the discup cradle. The symptom of this will be very little lever resistance and little driving force. One side will not react to steering well. If both are broken the mower will barely move.

6) Neutral rods (2) (5221)
These are the vertical threaded rods that have a spring sandwiched on top and bottom of the discup cradle casting.

7) Bearings(10) (5028, 5049)
If the bearings have lost contact with the shaft or if the bearing is loose or worn out it must be replaced if there is any play or looseness in any of the shafts.
Once it has been determined that all parts are in adequate condition, you may proceed with the following adjustments. Note that this applies only to the standard transaxle and not to Dixon’s Z-drive transaxle. The Dixon Z-drive transaxle has swing-out levers. It also contains no torque rods.


Step 1) Loosen the lock nuts on the 2166 pivot bolts at the rear of the trans.

Step 2) Loosen the outside lock nuts on the torque rods. (These are the two adjustment points.)

Step 3) Removing old gap. Turn the Allen head pivot bolt(2166) and the inside torque rod nut to push the cradle casting in toward the cone. This should be done by turning the torque rod nut 2 turns for every 1 turn of the pivot bolt as the T-rod is fine thread. Continue turning them until the discup cannot be turned because it is locked up on the cone. Be careful not to turn in too far as this could cause something to break. Just barely lock cup to cone.

Step 4) Squaring the discup. You must make sure that the discup is square with the back frame of the transmission. This can be done with a combination square or the Dixon special tool (5056). Release the front or rear that is more inboard than the other and adjust the outboard one in until the discup is square and it is still just barely locked on the cone.

Step 5) Setting the neutral gap. Loosen the adjustment bolts ever so slightly until the cups and cones just have a slight drag but no gap (You cannot move the discup up and down by hand.) Back off the pivot bolt about 2 flats(1/3 of a turn) and the T-rod nut 4 flats(½ a turn). This should give about a .020 to .025 gap between the cup and the cone. Try to do both sides the same. This will give a better result.

Step 6) Setting neutral. Make sure that the space between the bottom neutral rod lock and the lower spring nut contains about 5 threads. This holds the cradle up off the cone. Turn the upper spring nut down until the neutral gap is split between the upper and lower cones. This will change if the levers are not installed, i.e., if you have the trans out and you are doing this on the bench. If so, you will need to recheck this after the levers are on. Remember that one side goes up and one side goes down when you drive forward so the spring adjustments will look different on each side. This is normal.

Step 7) Final adjustments. Once the trans is all hooked up and ready to go make sure that the control rods are adjusted correctly. The lever stubs should be vertical or slightly rearward. The control levers should be even.
The torque rod inserts, if so equipped, (5185)should have the flat spot facing forward.

You should be able to roll the machine and not hear the cones rubbing on the cups. If needed, adjust the neutral spring nuts so the cones do not rub when rolling the machine.

Make sure you have locked all adjustments in place. Make sure the jam nuts are tight or you will lose your adjustment after a few hours of use.

Happy mowing!
Reply With Quote
  #5  
Old 05-16-2012, 12:43 AM
sunnyboy6977 sunnyboy6977 is offline
LawnSite Member
 
Join Date: May 2012
Posts: 1
Quote:
Originally Posted by efaubert1 View Post
Ok, my brother-in-law picked up a used Dixon 30" mower at an auction with a nice little 12hp Briggs for his small yard. It runs like a top, but it doesn't steer woth a darn. Now I have scoured the internet for cone adjustment, but it just isn't there. Amazing. Must be a million of these little mowers on the planet, yet how to adjust the drive must be the best kept repairman secret ever kept. So the question is, does anyone here know how to adjust them, and would you be willing to share the procedure please.
Did you ever find out how to adjust the cones? THANKS !!!
Reply With Quote
  #6  
Old 04-08-2014, 03:01 PM
OkieLand OkieLand is offline
LawnSite Member
 
Join Date: Apr 2014
Location: Oologah, OK
Posts: 1
YouTube has a 40 minute video of how to do that

https://www.youtube.com/watch?v=7QL-5bfMQxs

https://www.youtube.com/watch?v=FyGJQCYrBXs

Rebuild it
https://www.youtube.com/watch?v=Gzq_dxIrQkM

http://www.dixon-ztr.com/service-and...-66050&types=O

I found the OEM manual here for my DM-30
Reply With Quote
  #7  
Old 04-15-2014, 12:21 AM
mowermankevin mowermankevin is offline
LawnSite Senior Member
 
Join Date: Nov 2007
Location: Burleson,Texas 76028
Posts: 266
Dixon "Secrets"

Wow, where else would you get the first post of a person who has been on here since 2007 & one from a person who joined this month? Those lil' dixons are around, but I had a real learning lesson gettin it to go straight. This is an awesome website, Thanks Bonycells & Okie Land
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©1998 - 2012, LawnSite.com™ - Moose River Media
All times are GMT -4. The time now is 08:34 PM.

Page generated in 0.06641 seconds with 9 queries