wanted: transaxle for a Bobcat 52" ZTR

Discussion in 'Marketplace' started by pabble, Jun 13, 2011.

  1. pabble

    pabble LawnSite Member
    Posts: 10

    does anyone have for sale, or can anyone refer me to a good source for, a right transaxle for a 52" Bobcat ZTR model 942282? I would prefer used to keep the cost as low as possible - how much should I expect to spend? any help would be appreciated. thanks..........
     
  2. retrodog

    retrodog LawnSite Silver Member
    Posts: 2,420

    I am not a Bobcat dealer, but I can do some checking and make sure mine will fit yours. To help me start, what transmission is it: EZT, IZT, 2800, 3100, 3400, 5400? And what Bobcat is it: RZ procat etc.... I will call my buddy thats a bobcat dealer and see what we are looking at, I wouldn't mind giving you a killer deal to get you going again. I could also rebuild yours for you (depending on which one you had), but the shipping back and forth might make it too close to a new one. IZTs and up we could prolly rebuild for $100 to $150 each (depending on the condition when we open them up, if you are doing one might as well do the other, especially if they are sealed trannys. Give me a pm, I would like to help you out, and I might could get you a new one between $400 and $500 for a fellow lawnsiter......
     
  3. pabble

    pabble LawnSite Member
    Posts: 10

    hi, and thanks for the quick and welcome reply. This is a mower I have the opportunity to buy if I can find an economical solution to the mechanical problems. I contacted the seller last night asking for the info you mentioned and will get back to you as soon as I hear from him - would really like to have this mower so your help is very much appreciated. thanks again...bryan
     
  4. pabble

    pabble LawnSite Member
    Posts: 10

    Hi again....just heard from the seller and he gives this info:

    "The transaxle is a Eaton 778 Bobcat Part #4125850. The mower model name is a Leo 25. The hour meter shows 234. The pump head was seized on the shaft. A friend in our maintenance shop was able to get it removed but it did score the head shaft."

    does that help? what do you think? thanks. bryan
     
  5. rwaters

    rwaters LawnSite Senior Member
    from Online
    Posts: 731

    The part number you are looking for is 4129341 it is an eaton transmission and the badboy will not fit it as they use hydrogear. The price is kinda steep at list of $1,137.78 I have them for $959 each side.
     
  6. rwaters

    rwaters LawnSite Senior Member
    from Online
    Posts: 731


    sorry started the post before you did, you will find that that part number goes to the one I posted.
     
  7. pabble

    pabble LawnSite Member
    Posts: 10

    thanks for the quick and helpful info - do I understand correctly that I need to find part number 4129341 rather than the part number sent by the seller?
    bryan
     
  8. rwaters

    rwaters LawnSite Senior Member
    from Online
    Posts: 731

    They are the same part, if you can find the old part number it will be cheaper then my quote, but it is no longer available. The new part number is what I gave you the price on.
     
  9. rwaters

    rwaters LawnSite Senior Member
    from Online
    Posts: 731

    Also I am a bobcat dealer that is how I had the part numbers.
     
  10. pabble

    pabble LawnSite Member
    Posts: 10

    great...thanks for the clarification. I will need to do some research to find out if the total cost would make the effort worthwhile...the help is very much appreciated. bryan
     

Share This Page