Search Results for ‘hydro’

Picked up a Ex Mark 36in walk behind, with the FC420V Kawasaki. It hadn’t been ran for 2 years, I went through the engine completely, and have it running strong. I have yet to move the mower more than a few feet, not knowing a lot about the hydro system and what kind of shape it’s in after 2...

Hello, my name is Chris. I am new to this site. I'm not the owner of a lawn service, but I do mow my lawn and two neighbor's. Usually I use a push mower, garden tractor and string trimmer. Last year I purchased a well used Ferris Hydrowalk sd36. The machine needed a little tlc to get running...

I'm a teacher and mow about 10 yards over the summer. I also have no mechanical ability and last year when my Tiger Cat 52" went down, I was in a real panic for a week and had to tell some customers to wait. I'm looking for a backup mower to prevent that problem. My question is this: should I...

I have a 2012 scag v ride 52 inch with a 730 kawasaki engine and hydro gear pumps. Pump number: PG 1HQQ DA1X XXXX. While going up hill the right wheel starts to give out and will not go. When i have the break on and I press the left control it can spin the wheel over despite the break on the...

Exmark Turf Tracer X-Series Walk Behind, 60" Cut Kawasaki FX691V 22hp, ONLY 965 HOURS Comes with Mulch Kit. Recently Serviced, Runs and Cuts great. $2500 OBO LOCATED IN PORT CHARLOTTE, FL

Can someone please show me with a photo , where this bolts up to: Thank you. Scag SWZ-17KA OEM Frame Stiffener 422553 422552 Im rebuilding the entire mower , since the old frame was trashed. Almost all the welds were popped and the frame is cracking in other places.

Hey guys, I have a 2012 ish 930D with only 300 hours and the left hydro pump seems to have went out today while mowing. No warning noises at all... just stopped working. No leaks, fluid is good, linkage seems fine, right side works fine. The fan is not spinning on the left pump, and I can turn...

Morning all, I have an exmark 72" Lazer z with around 3k on it. I have lost some hydro pressure while going up an incline. I have replaced the hydro drive belt but same issue. I have also read through some posts and guy had similar issue and his bleeder valve was loose allowing pressure to...

Hi, I have a 1995 walker MTGHS with 2600h on it. bought it a couple of months ago. Engine has been replaced by the previous owner and everything works (power dump, hour-meter, alarms, newer wires etc) The “new” kohler 20hp has around 600h on it. Well at least it worked great until I got...

Good morning! Looking to buy a used walk behind. A gentleman is selling a fairly older model hydro snapper 48" walk behind. He claims it has a brand new pto but the engine(kawasaki) has no spark. My friend said he can probably get it going. He is asking $475. Is this issue listed above worth...

hey guys just curious if there is anything i can do to adjust the hydro pumps on a bobcat zt 225 model 942233a. just did fluid change on the pumps w/ filter ect but i have noticed that the left hydro is not as strong as the right hand side when going in a straight line and backing up ect. this...

Toro GrandStand 74559 52” Leaking hydraulic oil from left wheel motor. Slow leak. Only leaks when stopped after mowing, with the wheel on. When I took the wheel off, wiped the oil and grease off from around the motor, and put a fresh piece of cardboard under it and left it sit overnight (wheel...

Hi all, I just had my right hydro pump start leaking and I rebuilt it myself in 15 so I decided to just replace it. I installed the new pump and bled as per scag procedure. It worked fine for 10 minutes and the new pump started to rattle when you push the handles either way. It's like a clicking...

I have a 2013 52" Grandstand on which my dealer just installed a new Kawasaki 23.5 hp engine. While it was down I tryed a sit down zero turn, and it was much faster. I realize Toro does this for safety reasons but I'm a big boy, so how can I get my Grandstand to go about 5-7 mph faster???

Hi all, New member, though I have been searching and reading this forum for weeks trying to glean any small, helpful info to try and resolve the issue. There used to be LOTS of hustler info somewhere in the site, and it seems to have slowed. This is a hydro gear issue, so maybe someone who...

2013 Exmark Lazer Z X (LZX801KA606) with 29 HP Kawasaki engine. ISSUE - one side of the hydraulics stopped working, started to make a sound, etc. Pulled the dip stick off. Hydro oil smells burnt. Changed hydro oil and it ran for about 15 minutes and stopped working again. Any suggestions? Thank...

I've searched with no success in finding my problem, so here goes .... My mower, 36" Encore Premier Walk Behind, started to hesitate to move forward after start up or when starting up an incline. Hesitation last no more than 2 - 5 seconds then everything works fine (sometimes after a short...

Hey all, I just bought a 2010 IS2000z 61" and really like it, but on the right side when pulling it back into reverse it will go very slowly then suddenly kick in full speed. It is causing tears in the grass when it decides to kick in. The left side is smooth as silk. I haven't noticed any...

My old mower stopped moving forward or backwards, ran out of gas coming out of dichotomy & traffic barreling down rd. I shoved it off w/o pulling neutral rod on backside out, we'll now won't go , probably forced something apart? Belts still intact, see movement behind the leaver, wanted to...

has anyone changed the belt that drives the wheels on a 61 v ride. From what I can see I have to take the clutch off. Does that require a puller? If I need to do so. Please help.