1. Ask the Expert: Fertilization Strategies for Success: Dec. 12, 2017
    Learn how to do more with less when it comes to your fertilization services. Join the live Ask the Expert event hosted by Koch Turf & Ornamental: Dec. 12, 12-2 p.m. ET in the Fertilizer Application forum .

Meyer 8.5' Vector V-Plow

Discussion in '<a href=http://www.plowsite.com target=_blank ?>Sn' started by Lazer, Nov 19, 2000.

  1. Lazer

    Lazer LawnSite Bronze Member
    Messages: 1,446

    I'm a little disappointed guys. ;)

    I take pride in keeping abreast with snow-removal equipment. I figured with this forum and the knowledgeable guys who post here, there'd be no equipment I wasn't aware of and knew a little something about.

    For example, NO Meyer rep I've talked to knows HALF of what Chuck does about Meyer plows.

    Now I find out about a Meyer 8.5' V-plow called the "Vector" What's up with that? I'm not about to buy one, but does anyone else have more info?
  2. Chuck Smith

    Chuck Smith LawnSite Senior Member
    Messages: 849


    That's the V Meyer had out last year, or the year before even. It was recalled, because it was EXTREMELY weak.

    Most likely, it's why you have not heard about it at all. Then again, it has come up here before. No one mentioned the name, only that Meyer made a V plow they recalled.

    It was a must that it be powered by the E-60 pump. It was a full trip plow, not a trip edge design.

    I don't have the brochure here, but I do have one for it somewhere. If I can dig it up, I'll post more about it.

    Dino knows quite a bit about them, maybe he can enlighten us more.

    Well, just went over to the Meyer website, and lo and behold, the V is back! It's still called the EZ- Vector V plow. It says it's powered by the E-66 pump. Guess that's new too, never heard of it. Not much info on it. I'm a little disappointed that it looks like the old V they recalled. Hopefully they fixed the flaws. Still looks like tripping will be a problem. By that I mean it's design looks like it will be difficult for it to trip. A hard blow on the end of the cutting edge, doesn't look like it could trip the blade. Just an observation..... On their Power Units page, they don't even list or show a E-66. In the section where they match plows to vehicles, the V plow is not listed at all either.....



    [Edited by ChucksChevyPages on 11-19-2000 at 06:02 AM]
  3. Lazer

    Lazer LawnSite Bronze Member
    Messages: 1,446

    Powered by a V-66, which looks like a E-60 with the changed valves, but the parts don't interchange. Course Meyers "isn't in the snow-plow business", they're "in the parts business."

  4. GeoffDiamond

    GeoffDiamond LawnSite Bronze Member
    from Maine
    Messages: 1,651

    The Meyer V-plow came out in the Fall of 1998.

    Recalls began last winter I think?

    The Plow is yet to be put on the market yet. They never removed it from the web page.

  5. plowking35

    plowking35 LawnSite Bronze Member
    from S.E. CT
    Messages: 1,687

    Here is how meyer designed the plow.
    First they took a 8' husky and cut it down the center, installed a seriously weak hinge in the center,and welded the two halfs of the plow to it. Next they tried to copy boss and use trip spings to control the wing return. How they thought it would even trip in the v or scoop is beyond me. Unlike the boss that allows that entire center post to move, the hinge was welded to the swing sector.
    They has like 6 trip sprins for the moldboard, but I still cant see what good that would have done. The other side of the trip springs were attached in the same area that they usually are, along the top of the swing sector.
    The 6 meyer v plows that I saw recalled all were broken where the moldboard meets the center hinge point.
    I think the V-66 just had different valving to accomodate the v plow movement.
    The only benifit the meyer v plow had, was that you could pin it right to any meyer frame with out buying an entire new plow and sub frame. I think you could even get away with an older hydro power supply, as long as you ddint want to move both wings at the same time. But other than that, no benifits at all.
    Geoff I sure hope Meyer doesnt hack a good name like Diamond to pieces.
  6. John Allin

    John Allin LawnSite Bronze Member
    Messages: 1,488

    Oh... Give 'em time....

    I think those boys could screw up a wet dream.....
  7. GeoffDiamond

    GeoffDiamond LawnSite Bronze Member
    from Maine
    Messages: 1,651

    Well, So far Meyer has left the blade design of the Diamond alone. I Used to buy all fisher till the Diamond Pull away came out, because I don't love the Fisher Min Mount. So far Diamonds are a rock solid plow, and I have had a problem with the pumps, only I am only useing the E-60s.

    I think If I remember the story right, Diamond started to go under during the 80s, and thats when Meyer bought them out. That was when production of Diamond Plows stoped in Maine, and was Moved to Ohio. Diamond built one of the first v-plows and probably one of the best, but weighed too much for even a 1 ton.

  8. snow

    snow Guest
    Messages: 0

    In the fisher book, it said that a man introduced a v-plow design to dean fisher is the 70's. Fisher didn't buy the rights, so the man started up Diamond plows. Just a little history.

  9. GeoffDiamond

    GeoffDiamond LawnSite Bronze Member
    from Maine
    Messages: 1,651

    What book did you read this in? I might like to read it myself.

  10. snow

    snow Guest
    Messages: 0

    It's the book about the history of fisher plows. It was made for fisher's 50th anniversary. Everyone in sima that went on the fisher plant tour got a copy of the book.


Share This Page