1. Missed the live Ask the Expert event?
    Catch up on the conversation about fertilization strategies for success with the experts at Koch Turf & Ornamental in the Fertilizer Application forum.

    Dismiss Notice

new intake manifold --weekend project--

Discussion in 'Trucks and Trailers' started by 85w/350, Apr 30, 2001.

  1. 85w/350

    85w/350 LawnSite Member
    Messages: 244

    Hey guys, I decided to go with an edlebrock performer inatake for my 350. I have never replaced an intake manifold before but i have little fear about any work I do on my truck being that I am mechanically inclined and i have a few mechanic friends to refrence if need be. Anyone have any cautions for me? Any suggested gaskets? Or other things I should take a look at / replace while I have the intake off? Thanks for any two cents you have to offer.
  2. Mudbug44s

    Mudbug44s LawnSite Member
    Messages: 23

    Hmmm, I dont have any real tricks for changing intake manifolds. Just follow the directions to the letter, mark the distributor(Both the rotor position and the housing). Dont use the rubber end gaskets, use a 1/4" bead of RTV blue on the ends instead.

    Fel Pro has a neat gasket with a small screen across the runner openings, the theory is that they will help atomize fuel that is falling out of suspension. I Put them on a race Vega that I had and I liked them (I dropped a Nut down the intake and the screen kept it out of the valve). I cant vouch for the performance gain but some gizmos and gadgets are kinda neat.

    I just put an RPM air gap intake on a friends truck. I switched to ARP 12 point bolts and it sure made it nice for tightening the center two bolts on each side. Kinda expensive but what the heck.

    There is an old circle track trick of painting the bottom of your intake(The underside) White. The theory is that it will reflect more heat and keep the intake charge cooler. I dont like the Idea of paint peeling off the intake and falling into the lifter valley, it could cause a BIG headache.

    One last thing, Try to keep all the old gasket material out of the lifter valley. Stuff some rags into the intake holes in the head to keep them free of dirt. I use a shop vac to clean out the whole area when I have it all scraped clean. Good luck, and Have FUN.

  3. 85w/350

    85w/350 LawnSite Member
    Messages: 244

    Thanks for the reply. Wierd that they paint the underside white..what color does it really matter that the underside is if its never reflecting light. If its heat seams like just the paint coating is doing it. i personally dont like the idea either. I'll be sure to use the RVT Blue and I am cautious with the cleanliness of any project i approach. :)
  4. Garet

    Garet LawnSite Member
    Messages: 157

    Make sure that the gasket does not get out of place when you install the manifold. I had it do this once which fouled everything up. Also, make sure you have the torque pattern. This will aid in getting the thing on straight and proper. If the Fel Pro gasket is expensive I wouldn't use it. I would just go with a standard gasket. Besides making sure you have a good clean surface, that's about all that really matters.
  5. 85w/350

    85w/350 LawnSite Member
    Messages: 244

    I'm not worried about the expense of a gasket...I have been contemplating a new intake for quite some time now. I think ALOT about things before I begin work on them on my truck so when i do it i get it done right the first time. So a good gasket is all i will settle for despite the extra few bucks. Think about it...the intake is a major part of an engine and anything that can get in and out thats not going in the right place is BAD. Thanks for suggesting the torque specs and pattern...Anyone know of any amount of time i should definately let it sit before starting it? Maybe the liquid gasket if by any possibility wouldnt be dry would be at a later period of time?
  6. MTCK

    MTCK LawnSite Senior Member
    from Idaho
    Messages: 254

    When I put that manifold on my truck, I believe it sat for about 2 weeks befor the engine was fired, but this was mainly because the body was off the frame at the time. I'd imagine it would be fine after 2 hours or so. They only thing you'd be waiting on is the RTV at the ends, and they only see oil, not coolant right? To be on the safe side maybe let it sit over night. I don't really think it's necessary though. It's hard to not drive something after you make an improvement to it :) Good luck.

  7. 85w/350

    85w/350 LawnSite Member
    Messages: 244

    How do you like the manifold? I emailed the people at edelbrock with my engine specs and they said probably a 10-15hp increase. Better throttle response. My engine is basically stock just a fre flowing exhaust system. I can't wait to get to the weekend and I know its gonan be hard to just let it sit... :)
  8. MTCK

    MTCK LawnSite Senior Member
    from Idaho
    Messages: 254

    I like it, the throttle response is deffinetly better, along with the low end torque. I was planning on putting a 383 in my truck, so I put a performer 750 carb on it, and it's way too big, but by rejetting it, it works ok. I also am running dual 3" exhaust with hedman headers, and flowmaster mufflers, and a hotter ignition. I did all the mods at the same time, and it deffinetly brought the engine to life. Drivability is a lot better. Let us know how you like yours.
  9. 85w/350

    85w/350 LawnSite Member
    Messages: 244

    Sure thing...I also have flowmaster exhaust and MSD ignition...all the other small things are there I just think this is going to connect everything else. Thanks for the feedback!
  10. Alan

    Alan Member
    Messages: 1,185

    I've got a Performer intake on the 350 in my GMC 5500. 4spd with 2 spd rear. Granted, it's geared low, 6.65 high, 8.82 low range, but it pulls something fierce. I try to keep revs between 2,00 and 3,500. Grossing 21,000 I can come off a dead stop in second low without touching the throttle. Carb is a 600 Holley with electric choke.

Share This Page