1. Ask the Expert: Fertilization Strategies for Success: Dec. 12, 2017
    Learn how to do more with less when it comes to your fertilization services. Join the live Ask the Expert event hosted by Koch Turf & Ornamental: Dec. 12, 12-2 p.m. ET in the Fertilizer Application forum .

Tearing up turf with a ZTR

Discussion in 'Lawn Mowing' started by bentleytn, May 17, 2010.

  1. bentleytn

    bentleytn LawnSite Member
    from TN
    Messages: 14

    Anybody with some driving advice. We have had a bunch of rain in TN and the ground is very soft, with our ZTR we are consistently tearing up turf in turns. Not the most experienced so some driving advice, much appreciated. Thanks.
  2. crhoades68

    crhoades68 LawnSite Member
    from Indiana
    Messages: 71

    Most manuals will show you the proper way to turn a ZTR. The best method I've found in wet conditions is to add a 2nd header lap/outer ring to increase your turn space and then continue to use the Y turn. Turn slightly into or away from (your preference) your next line and then back into your next line. Make these turns slower on wetter ground and remember that both rear/drive wheels need to be moving or you will tear up the turf regardless of the conditions.

    One other thought is that based on the amount of rain you received it may be best to wait a while. You could end up doing more damage by trying to mow than just letting the grass grow and mowing multiple times (using different patterns) once the ground has dried some. Good luck!
  3. ZTR_Diesel

    ZTR_Diesel LawnSite Senior Member
    Messages: 371

    I live in a sandy valley region of Illinois near the Illinois river. I have to take it super-slow on turns, especially in newer housing developments where most of the black topsoil has been scraped off and sold for profit.

    I generally use a three-point turn, and take minimum two, but preferably three outlining laps prior to mowing in the middle.

    However - the big question mark, since it sounds like you have employees is how to get them to do all this. You have to enforce it - have them go and repair a few "divits" in some yards sometime and it may help. I agree also with the wait till it's dry theory. Good luck!

    MS_SURVEYOR LawnSite Bronze Member
    Messages: 1,002

  5. SouthSide Cutter

    SouthSide Cutter LawnSite Bronze Member
    Messages: 1,331

    You have to do the same thing going around trees even though it is a bigger arch cause it will still teat up the turf

    MS_SURVEYOR LawnSite Bronze Member
    Messages: 1,002

    Yea! I stopped ringing around trees. Go in, back out, back in, then out, and so on. That stopped that torn turf around trees and bushes Seems like it takes longer, but looks better.
  7. jnt412

    jnt412 LawnSite Member
    Messages: 60

    When turning, make sure the inner wheel is slowly moving. If it doesn't turn the turf will be damaged. Years back it took me a week to adjust..
  8. watson524

    watson524 LawnSite Member
    Messages: 72

    And in my experience (I'm a residential who cuts a lot of grass) at least on the Scags and Land Pride I've used, you have to pull back harder on the inside wheel than you push forward on the outside wheel. One tip someone gave me a while back was to get going in reverse, then only move your outside hand forward, keep the inside hand where it was.
  9. bentleytn

    bentleytn LawnSite Member
    from TN
    Messages: 14

    you guys are great, thanks. i'm assuming that mowing straight (I grew up on tractors) gets easier and easier on zero turns.
  10. watson524

    watson524 LawnSite Member
    Messages: 72

    My best advice, and again, I'm but a wee novice compared to most folks here, but it's like driving my boat really. Pick a point and mow to it (like a tree or something depending what's on your grass' "horizon"). Don't look down at the grass right in front of you or the caster, deck edge, etc.

Share This Page