1. Can’t make it to the GIE+EXPO 2017?
    LawnSite brings the trade show floor to your fingertips with our new GIE+EXPO 2017 Sneak Peek video series debuting now in the Lawn Mowing forum.

    Dismiss Notice

The new Super Z Any updates?

Discussion in 'Lawn Mowing Equipment' started by HenryB, Feb 12, 2012.

  1. mtmower

    mtmower LawnSite Bronze Member
    Messages: 1,111

    Mic. Has it dried out at all there? Any better luck with clippings if so? I'm also about to buy the identical mower.
  2. Mickhippy

    Mickhippy LawnSite Platinum Member
    Messages: 4,274

    Had showers last few days (again), but was able to do a few yesterday. Its hard mate, 2 weekly cut grass is long and damp so very frustrating. I am getting windrows in long grass where I wasnt with the xr7. If not taking much off its not too bad.

    You know on the xr7 deck they had that angled piece of steal in the discharge chute? I think clippings are getting caught on that with this new deck. Clippings come out the full width of the chute, maybe they shouldnt!

    I really think you need a good demo before buying.
  3. Ridin' Green

    Ridin' Green LawnSite Fanatic
    Male, from Michigan
    Messages: 17,100

    I might be wrong, but IIRC you cut with your OCDC all the way up in the straight up position. I have read that the discharge chute being wide open can cause the clumping issue, s last summer I tried a little experiment with my 7 Iron. I had the chute all the way up for a while on one place Like I used to always do, and did get a little windrowing. Then I let it back down in its normal position sticking basically straight out to the side, and no more windrowing at all. I tried it a few more times over the sumer with the same results, so maybe there's something to that after all. Try it with the OCDC straight out and see if it helps. Worth a shot.
  4. StanWilhite

    StanWilhite LawnSite Silver Member
    Messages: 2,352

    Sorry about that.......:laugh:
  5. Mickhippy

    Mickhippy LawnSite Platinum Member
    Messages: 4,274

    I mow with the ocdc fully open but I have tried mowing with the deflector chute on with same, or worse windrowing. But I could easily try closing it a bit but I cant see how that will effect the clippings before they even hit it. I'll give it a go though, cant hurt!

    Stan, I forgive you! Maybe????
  6. trooper8870

    trooper8870 LawnSite Member
    Messages: 241

    Have you figured out what the fuel consumption per hour is yet?
  7. Mickhippy

    Mickhippy LawnSite Platinum Member
    Messages: 4,274

    Best ive had so far is 3.5hrs almost to the minute out of one tank of 25Lt
    About 7.15Lt/hr or 1.88Gal/hr

    Fuel cost $1.50/lt so $10/hr
  8. mtmower

    mtmower LawnSite Bronze Member
    Messages: 1,111

    This kills me to hear. I found a left over for $10800.00 and suspension seat. I love the way they're built. Wish they held more fuel capacity and had an isolated platform but that's not what will keep me from buying. The stupid thing has got to cut and leave the clippings properly. First and for most that's what any mower has got to do well. The perks come later like, performing it faster and lasting longer. I hope you find the fix. From what I'm reading the high lifts might be helpful. It would be worth a try.

    I'm looking at the Gravely Pro Turn 400 which is new this year, costs as much $11300.00, has no proven track record, less warranty, and probably not built as heavy duty. It does have an air seat, isolated platform, 13 mph, and 13.4 gal tanks.

    Also looking at the Husqvarna PZ6034FXZT. Found one for $8900.00 but I have to travel for it. No big deal. It's been out longer then the 400. But again less warranty, probably not built as heavy duty, and only 11 gallon tanks. It also has the isolated deck and the super high two speed hydro deal like the Cheetahs which is not proven.

    Not to sound like the broken record but I can't demo any of these prior to buying. I know Hustler but hate the previous decks cuts. Accessories for the PZ and the 400 cost less (exp. bagging system roughly $1000.00 less) but they may not cut any better then the VX4. What to do. What to do.
  9. Mickhippy

    Mickhippy LawnSite Platinum Member
    Messages: 4,274

    Dont do anything until you demo! You'll love driving it. Only issue Im having is the discharge and the frickin fuel tanks! Seriously, you need to demo even if you have to drive 2hrs to do it.

    You will love the machine. I bet it will be the best ztr you have ever driven and Im not having issues with the cut itself, just the discharge. Thats the only thing I reckon you need to worry about.
  10. dwayne4

    dwayne4 LawnSite Member
    Messages: 5

    I have 77.8 hours on mine. Its the best mower on the market right now. Durability, cut, ease of use, speed, and a profitable mower. I am not brand sensitive, I just know what works.
    Last edited: Mar 17, 2012

Share This Page